3
SAFE
IMPORT
V
Y
Connection to a line voltage other than that for which it is intended can
create a safety and fire hazard and may damage the unit.
If you have any questions about the volta
model, or about the line volta contact your selling dealer
before plugging the unit into a wall outlet.
Do Not Use Extension Cords
T use only the power cord attached to your unit.
We do not recommend that extension cords be used with this product. As
with all electrical devices, do not run po
place heavy objects on them. Damaged power cords should be replaced
immediately by an authorized ser
specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the
plug; never pull the cord. If you do not intend to use the unit for an
considerable length of time, disconnect the plug from the AC outlet.
Do Not Open the Cabinet
There are no user Opening the
cabinet may present a shock hazard, and an
will void your warranty If water or an
wire or staple accidentally falls inside the unit, disconnect it from the
power source immediately
CA
If an outside antenna or cable system is connected to this product, be
certain that it is grounded so as to provide some protection against volta
surges and static charges. Section 810 of the National Electrical Code,
ANSI/NFP provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes and require-
ments of the grounding electrode.
NOTE TO CA This reminder is provided
to call the CA
the NEC, which provides guidelines for proper grounding and, in particular
specifies that the cable ground shall be connected to the grounding system
of the building, as close to the point of cable entry as possible.
Installation Location
•
place the unit on a firm and level surface. When placing the unit on a
shelf, be certain tha
the weight of the product.
• Make certain that proper space is provided both above and below the
unit for ventilation. If this product will be installed in a cabinet or other
enclosed area, make certain that there is sufficient air movement within
the cabinet. Under some circumstances, a fan may be required.
• Do not place the unit directly on a carpeted surface.
• or in an area that is
exposed to direct sunlight or heating equipment.
•
• Do not obstruct the ventilation slots on the top of the unit, or place
objects directly over them.
• Due to the weight of the
fiers, there is the remote possibility that the rubber padding on the bottom
of the unit’
Use caution when placing the unit on soft woods or other materials that
may be damaged by heat or hea Some surface finishes may be
particularly sensitive to absorbing such marks, due to a variety of factors
beyond our control, including the nature of the finish, c
used, and normal hea
or other factors. Wcised in choosing
an installation location for the component and in normal maintenance
practices, as your warranty will not cover this type of damage to furniture.
Cleaning
When the unit gets dirty wipe it with a clean, soft, dry cloth. If necessary
and only after unplugging the
dampened with mild soapy water then a fresh cloth with clean water Wipe
it dry immedia aerosol cleaners,
thinner Do not use abrasive
cleaners, as they may damage the finish of metal parts. Avoid spraying
insecticide near the unit.
Moving the Unit
Before moving the unit, be certain to disconnect an
with other components, and make certain tha
the AC
Important Information for the User
This equipment has been tested and found to comply with the limits for a
Class-B digital device, pursuant to Part 15 of the FCC Rules. The limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radia
radio-frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communica
However there is no guarantee that harmful interference will not occur in
a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encoura
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful inter-
ference, and (2) this device must accept interference received, inc
interference that may cause undesired operation.
NOTE: Changes or modifications may cause this unit to fail to comply with
Part 15 of the FCC Rules and may void the user’
equipment.
UNP
The carton and shipping materials used to protect your new receiver during
shipment were specially designed to cushion it from shock and vibration.
We suggest that you save the carton and packing materials for use in ship-
ping if you move, or should the unit ever need repair
T you may wish to flatten it.
This is done by carefully slitting the tape seams on the bottom and collaps-
ing the carton. Other cardboard inserts may be stored in the same manner
Packing materials that cannot be collapsed should be saved along with the
carton in a plastic bag.
If you do not wish to save the packaging ma please note that the
carton and other sections of the shipping protection are recyc Please
respect the environment and discard those materials at a local recycling
center
It is important that you remove the protective plastic film from the front-
panel lens. Lea
remote control.
AVR 2600 OM.qxd 4/29/09 12:10 PM Page 3
