Bedienungsanleitung Harman Kardon AVR35 (Seite 14 von 45) (Englisch)

502644

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

Remote Control Functions

IMPORTANT NOTE: The AVR35’s

remote may be programmed to con-

trol up to five additional devices,

including the AVR35. Before using

the remote, it is important to remem-

ber to press the Device Control

Selector button bcthat corre-

sponds to the unit you wish to oper-

ate. In addition, the AVR35’s remote

is shipped from the factory to oper-

ate the AVR35 and Harman Kardon

CD players and cassette decks. The

remote is also capable of operating

a wide variety of other products

using the control codes that are part

of the remote. Before using the

remote with other products, follow

the instructions on pages 28–29 to

program the proper codes for the

products in your system.

It is also important to remember that

many of the buttons on the remote

take on different functions, depend-

ing on the product selected using

the Device Control Selectors. The

descriptions shown here primarily

detail the functions of the remote

when it is used to operate the

AVR35. (See pages 28–31 for infor-

mation about alternate functions for

the remote’s buttons.)

a Program/Command Indicator:

This LED is used as an indicator to

assist in programming the remote

control. (See pages 28–31 for more

information on programming the

AVR35.)

b AVR Selector: Press this button

to use the remote control for operation

of the AVR35. Note that the button will

briefly turn red after it has been

pressed to confirm your selection.

c Device Control Selectors:

Press one of these buttons to use the

remote to control the functions of

another audio/video device. Note that

the button will briefly turn red after it

has been pressed to confirm your

selection. (See pages 28–31 for infor-

mation on programming the AVR35’s

remote to operate these devices.)

d Power Button: Press this button

to turn the currently selected device

on or off.

e Sleep Button: Press this button

to place the unit in the Sleep mode.

After the time shown in the display,

the AVR35 will automatically go into

the Standby mode. Each press of

the button changes the time until

turn-off in the following order:

f Channel

⁄

Buttons:

When the remote is being used to

control a TV, VCR or Cable box, press

these buttons to change the channel

being viewed.

g Surround Mode Selector: Press

this button to begin the process of

changing the surround mode. After

the button has been pressed, use

the

⁄

buttons h to select the

desired surround mode. (See page

24 for more information.)

⁄

Buttons: These are multi-

purpose buttons. They will be used

most frequently to select a surround

mode. To change the surround mode,

first press the SURR button g. Next

press these buttons to scroll up or

down through the list of surround

modes that appear in the Information

Display

. (See page 24 for more

information.) These buttons are also

used to increase or decrease output

levels used to lower the AVR35’s out-

put levels when configuring the unit

with either the internal test tone or

an external source. (See pages 19

and 26 for more information.) They

are also used to enter delay time

settings after the Delay button x

has been pressed. (See page 20 for

more information.)

min

OFF

‹

/Channel Button: This

button is used to start the process

of setting the AVR35’s output levels

to an external source. Once this but-

ton is pressed, use the

⁄

buttons

h to select the channel being

adjusted, then press the Set button

j, followed by the

⁄

buttons

again to change the level letting.

(See page 27 for more information.)

j Set Button: This button is used

to enter settings into the AVR35’s

memory. It is also used in the setup

procedures for delay time, speaker

configuration and channel output

level adjustment. (See pages 17–21

for complete information.)

k Night Mode: Press this button

to activate the “Night” mode, pre-

venting loud playback when the

digital modes are in use without

altering the dynamic range of the

output signal.

l Source Selectors: Press these

buttons to select an input source for

the AVR35. The AM/FM button is also

used to switch between frequency

bands when the tuner is in use.

NOTE: Pressing one of these buttons

selects the source only. In order to

control the actual source machine

using the remote you must press the

Device Control Selector button c

for the desired product.

m +10 Button: This button does

not have a function for the AVR35,

but when the remote is used to con-

trol certain CD players, TV sets and

VCRs it may be used to select tracks

or channel numbers

n Numeric Keys: These buttons

serve as a ten-button numeric key-

pad to enter tuner preset positions.

They are also to be used to select

channel numbers when TV has been

selected on the remote, or to select

track numbers on a CD, DVD or LD

player, depending on how the

remote has been programmed.

AVR35 om (H) 2/5/99 10:41 AM Page 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR35 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info