Bedienungsanleitung Harman Kardon AVR35 (Seite 33 von 45) (Englisch)

502644

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

Programming the Remote

Example: To program your TV,

Cable Box and the AVR35 to turn on

when the Power button is pressed,

first press-and-hold the AVR b

and Mute buttons ` until the red

light comes on under the AVR but-

ton. Next, press the Mute button

` to enter the Power command

for the AVR. Press the TV Device

Control Selector c to select

the TV mode, and then press the

Mute button ` again, to select

TV Power. Finally, press the CBL

Device Control Selector c

followed by the Mute button `

to select Cable Power. Press the

Channel

⁄

buttons f to

enter the commands.

After following these steps, each time

you press the Power button d, the

remote will send the Power On/Off

command each time the Power

button is pressed.

To remove a macro program, follow steps

1, 2 and 4 above, but do not follow step

three. For example, to erase the macro

just entered, press the Device Control

Selector c and the Mute button `

at the same time until the red light

under the Device Control Selector turns

on. Press the Power button d, and

then press the Channel

⁄

buttons

f. The red light under the Device

Control Selector will blink twice to

confirm the data entry and then turn off.

NOTE: Only the AVR button b and

the SAT/CBL button c may be pro-

grammed for macros.

Volume Punch-Through

The AVR35’s remote may be programmed

to operate the Volume Controls

from either the TV or the AVR to operate in

conjunction with any of the eight devices

controlled by the remote. For example,

since the AVR35 will likely be used as the

sound system for TV viewing, you may

wish to have the AVR’s volume activated

although the remote is set to run the TV.

Either the AVR or TV volume control may

be associated with any of the remote’s

devices. To program the remote for Volume

Punch-Through, follow these steps:

1. Press the Device Control Selector

c for the unit you wish to have asso-

ciated with the volume control and the

Mute button ` at the same time

until the red light illuminates under

the Device Control Selector.

2. Press the Volume Up button .

3. Press either the AVR b or the TV

Device Control Selector c,

depending on which system’s volume

control you wish to have attached for

the punch-through mode. Note that

the red light under the Device

Control Selector will blink twice

and then go out to confirm the data

entry.

Example: To have the AVR’s

volume control be activated even

though the remote is set to control

the TV, first press the TV Device

Control Selector c and the

Mute button ` at the same time.

Next, press the Volume Up button

followed by the AVR Device

Control Selector b.

NOTE: Should you wish to return the

remote to the original configuration after

entering a Volume Punch-Through, you

will need to repeat the steps shown above.

However, press the same Device Control

Selector in steps one and three.

Re-Assigning Device Control

Selectors

Although each of the seven Device

Control Selectors c is normally

assigned to the category of product shown

on the remote, it is possible to re-assign

one of these buttons to operate a second

device of another type. For example, if you

have two VCRs, but no satellite receiver,

you may program the “SAT” button to

operate a second VCR. Before following

the normal programming steps for either

Three-Digit entry or Auto Search code

entry, you must first re-assign the button

with the following steps:

1. Press the Device Control Selector

c you wish to re-assign and the

Mute button ` at the same time

until the red light illuminates under

the Device Control Selector.

2. Press the Device Control Selector

c for the function you wish to

program into the re-assigned button.

3. Enter the three-digit code for the spe-

cific model you wish the re-assigned

button to operate.

4. Press the same Device Control

Selector pressed in Step 1 again to

store the selection.

Example: To use the SAT button to

operate a second VCR, first press the

SAT Device Control Selector

c, and the Mute button ` at

the same time until the red light

glows under the SAT button. Press

the VCR button, followed by the

three-digit code for the specific

model you wish to control. Finally,

press the SAT button again.

AVR35 om (H) 2/5/99 10:41 AM Page 31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR35 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info