3
Important Safety Information
Verify Line
Y Connection to
a line voltage other than that for which it is intended can create a safety and fire
hazard and may damage the unit.
If you have any questions about the voltage requirements for your specific model, or
about the line voltage in your area, contact your selling dealer before plugging the unit
into a wall outlet.
Do Not Use Extension Cords
T use only the power cord attached to your unit. W
recommend that extension cords be used with this product. As with all electrical
devices do not run power cords under rugs or carpets or place heavy objects on
them. Damaged power cords should be replaced immediately by an authorized service
center with a cord meeting factory specifications
Handle the
When disconnecting the power cord from an never
pull the cord. If you do not intend to use the unit for any considerable length of time
disconnect the plug from the
Do Not Open the Cabinet
There are no user Opening the cabinet
may present a shock hazard, and any modification to the product will void your
guarantee If water or any metal object such as a paper clip wire or staple acciden-
tally falls inside the unit, disconnect it from the and
consult an authorized service center
CA
If an outside antenna or cable system is connected to this product, be certain that it is
grounded so as to provide some protection against voltage surges and static charges
Section 810 of the National Electrical Code ANSI/NFPA No 70-1984, provides
information with
respect to proper grounding of the mast and supporting structure
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conduc-
tors location of antenna discharge unit,
connection to grounding electrodes and
requirements of the grounding electrode
NOTE This reminder is provided to call the CA
(cable which provides
guidelines for proper grounding and, in particular specifies that the cable ground
shall be connected to the grounding system of the building
of cable entry as possible
Installation Location
• place the
unit on a firm and level surface When placing the unit on a shelf be certain that
the shelf and any mounting hardware can support the weight of the product.
• Make certain that proper space is provided both above and below the unit for
ventilation. If this product will be installed in a cabinet or other enclosed area,
make certain that there is sufficient air movement within the cabinet. Under some
circumstances a fan may be required.
• Do not place the unit directly on a carpeted surface
• or in an area that is exposed
to direct sunlight or heating equipment.
•
• Do not obstruct the ventilation slots on the top of the unit, or place objects
directly over them.
• Due to the weight of the
there is the remote possibility that the rubber padding on the bottom of the
unit’s feet may leave marks on certain wood or veneer materials Use caution
when placing the unit on soft woods or other materials that may be damaged
by heat or heavy objects. Some surface finishes may be particularly sensitive to
absorbing such marks due to a variety of factors beyond our control, including
the nature of the finish, cleaning materials used, and normal heat and vibration
caused by the use of the product, or other factors We recommend that caution
be exercised in choosing an installation location for the component and in normal
maintenance practices
Cleaning
When the unit gets dirty wipe it with a clean, soft, dry cloth. If necessary and only after
unplugging the
water then a fresh cloth with clean water Wipe it dry immediately with a dr
NEVER use benzene aerosol cleaners thinner
agent. Do not use abrasive cleaners as they may damage the finish of metal parts
Avoid spraying insecticide near the unit.
Moving the Unit
Before moving the unit, be certain to disconnect any interconnection cords
with other components and make certain that you disconnect the unit from
the AC
Important Information for the User
This equipment has been tested and found to comply with the limits for a Class-B
digital device pursuant to Part 15 of the FCC Rules The limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation.
This equipment generates
uses and can radiate radio-frequency energy
and, if not
installed and used in accordance with the instructions may cause harmful interfer-
ence to radio communication. However there is no guarantee that har
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules Operation is subject to the
following two conditions: (1) this device may not cause harmful interference
(2) this device must accept interference received, including interference that may
cause undesired operation.
NOTE: Changes or modifications may cause this unit to fail to comply with Part
15
of the FCC Rules and may void the user’s authority to operate the equipment.
Unpacking
The carton and shipping materials used to protect your new receiver during ship-
ment were specially designed to cushion it from shock and vibration. We suggest
that you save the carton and packing materials for use in shipping if you move or
should the unit ever need repair
T you may wish to flatten it. This is done
by carefully slitting the tape seams on the bottom and collapsing the carton. Other card-
board inserts may be stored in the same manner Packing materials that cannot be col-
lapsed should be saved along with the carton in a plastic bag
If you do not wish to save the packaging materials please note that the carton and
other sections of the shipping protection are recyclable Please
respect the environ-
ment and discard those materials at a local recycling center
It is important that you remove the protective plastic film from the front-panel lens
Leaving the film in place will affect the performance of your remote control.
SAFETY INFORMA
AVR354 OM.qxd 9/26/08 12:25 PM Page 3
