Bedienungsanleitung Harman Kardon AVR354 (Seite 12 von 76) (Englisch)

502622

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

REAR-PANEL CONNECTIONS

• The Analog 1 and 2 connectors don’t physically line up with

any analog video inputs. Consider using them for audio-only

devices, such as a CD player or cassette tape deck.

• The Analog 2 and 4 inputs are each associated with a set of

outputs. Consider using the Analog 2 connectors for an audio

recorder, and the Analog 4 connectors for a video recorder

(along with the Video 2 connectors).

• You may optionally connect a source to both an analog and

digital audio input. This is useful for making recordings, for

multizone applications or simply as a backup.

Analog 2 and 4 Outputs: Connect either of these analog audio

outputs to the analog audio inputs of a recording device. A signal is

available at these outputs whenever an analog audio source is playing.

However, the AVR 354 does not convert digital audio sources to analog

for recording.

Coaxial 1/2 and Optical 1/2/3 Digital Audio Inputs: If a

source has a compatible digital audio output, and if you are not using

an HDMI connection for audio for the device, connect it to one of these

jacks to hear digital audio formats, such as Dolby Digital, DTS and linear

PCM. Use only one type of digital audio connection for each source.

Coaxial Digital Audio Output: If a source is also an audio

recorder, connect a coaxial digital audio output to the recorder’s input

for improved recording quality. Only PCM digital audio signals (coaxial

and optical) are available for recording.

The Bridge II Input: Connect the included Harman Kardon

docking station to this input for use with most docking

iPod models, 4G and later (not included). Make sure the receiver is

turned off (in Standby mode) when connecting The Bridge II.

6-/8-Channel Inputs: Connect the multichannel analog audio

outputs of a DVD-Audio, SACD

™

, Blu-ray Disc

™

or HD-DVD

™

player

(or any other external decoder) to these jacks to enjoy these formats.

NOTE: When the multichannel player has an onboard digital

decoder, it is not necessary to connect it to the 6-/8-Channel

Analog Audio Inputs. Only a digital audio connection (HDMI,

coaxial or optical) is needed.

Zone 2 Audio Outputs: Connect these jacks to an external amplifier

to power the speakers in the remote zone of a multizone system. When

these jacks are used, it is possible to have a full 7.1-channel system in

the main listening room at the same time the multizone system is in use.

Component Video 1, 2 and 3 Inputs: If a video source (e.g.,

DVD player or HDTV tuner) has analog component video (Y/Pb/Pr)

capability, and if you are not using an HDMI connection for the device,

then connect the component video outputs of the source to one of the

sets of component video inputs. Do not make any other video connec-

tions to that source.

Component Video Monitor Outputs: If you are using one of

the Component Video Inputs and your television or video display is

component-video-capable, and if you are not connecting the HDMI

Output to your display, connect these jacks to the corresponding inputs

on your video display.

NOTES:

• Due to copy-protection restrictions, there is no output at

the Component Video Monitor Outputs for copy-protected

sources.

• Composite and S-video signals are upscaled to as high as

1080i and available at these outputs. If your video display’s

best connection is component video, it is the only video

connection required from the AVR to the display.

RS-232 Serial Port: This specialized connector may be used with

your personal computer in case we offer a software upgrade for the

receiver at some time in the future.

RS-232 Mode: Leave this switch popped out in the Operate position

unless the AVR 354 is being upgraded.

RS-232 Reset: This switch is only used during a software upgrade.

A standard processor reset is performed by pressing and holding the

front-panel OK Button.

Switched AC Accessory Outlet: You may plug the AC power

cord of one source device into this outlet, and it will turn on whenever

you turn on the receiver. Do not use a source that consumes more than

50 watts of power.

AC Power Input: After you have made all other connections, plug the

AC power cord into this receptacle and into an unswitched wall outlet.

AVR354 OM.qxd 9/26/08 12:26 PM Page 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR354 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info