Bedienungsanleitung Harman Kardon AVR40 (Seite 14 von 24) (Englisch)

502645

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Installation and Configuration

Your new Harman Kardon receiver is

designed to provide the best reproduction

from both movies and musical pro-

grams. To assure that the unit operates to

its fullest capability, it is important that

you spend a few minutes to properly

install and configure all of the elements

in your new system. Some, or all of the

following steps will apply to your system,

depending on the equipment in use. If

you have any questions concerning the

installation of this product consult your

local dealer, or contact the Harman

Kardon web site at

www.harmankardon.com

System Component Connections

IMPORTANT SAFETY NOTE: Many

products feature automatic turn on cir-

cuitry which may accidentally be activated

when making connections. For your own

safety and to prevent damage to speakers,

amplifiers and other components we

strongly recommend that all equipment

power be turned off at the Main Power

Switch

, or that AC power cords be

unplugged when any system connections

are made or changed.

Using high-quality interconnect cables,

connect all source components to the

appropriate input jacks on the rear

panel. When connecting audio recorders

and VCRs it is important to make certain

that the PLAY/OUT jacks on the recorders

are connected to the PLAY jacks on the

AVR40, and that the RECORD/IN jacks of

the recorders are connected to the REC

jacks on the AVR40.

Assemble the supplied AM loop antenna

as shown below and connect it to the AM

ANTENNA Terminals f.

It may be necessary to rotate the antenna

or change its position to achieve the best

AM reception. Connect an FM antenna to

the FM ANTENNA Terminal g. A

300-ohm to 75-ohm adapter may be

required for some antennae.

If you are using the AVR40 to switch

video inputs, connect the Monitor out-

put ‚ to a video input on your TV or

projector.

The rear panel accessory outlets on the

AVR40 may be used to power low current

devices such as CD players or tape decks.

The SWITCHED Accessory AC

Power Outlets ﬂ are activated only

when the AVR40 is turned on. The

UNSWITCHED Accessory AC

Power Outlets ﬁ may be used with

VCRs, as the power to these outlets is live

as long as the AVR40 remains connected

to an AC power source.

CAUTION: The total power load for all

products connected to the accessory out-

lets must not exceed 100 watts. Do not

use them for high current devices such as

power amplifiers.

If the AVR40’s front panel remote sensor

is blocked by cabinet doors you may

still operate the unit via remote control

with the use of an optional external

remote sensor. Connect the output of the

sensor to the rear panel REMOTE

CONTROL Extension Input ·. This

AM LOOP ANTENNA SETTING

Stand and place it on a shelf, or hang it on a wall.

LEG

jack may also be used as the IR input

from compatible multiroom control

systems. The AVR40’s remote sensor may

be looped to other components by con-

necting the REMOTE CONTROL

Extension Output ° to the IR

remote input jack of other compatible

components.

Speaker Selection and Placement

Depending on the type of center channel

speaker in use and your viewing device,

place the center speaker directly above or

below your TV.

Once the center channel speaker is

installed, position the left and right front

speakers so that they are as far away

from one another as the center channel

speaker is from the preferred listening

position. Ideally, the front channel

speakers should be placed so that their

tweeters are no more than 24″ higher

or lower from the tweeter in the center

channel speaker.

Depending on the specifics of your room

acoustics and the type of speakers in use,

imaging may be improved by moving the

front left and right speakers slightly for-

ward of the center channel speaker. If

possible, adjust all front loudspeakers so

that they are aimed at ear height when

you are seated in the listening position.

Using these guidelines, you may find that

it takes some experimentation to find the

correct location for the front speakers in

your particular installation. Don’t be

afraid to move things around until the

system sounds correct. Optimize speaker

locations so that pans across the front of

the room sound smooth, and that sounds

from all speakers appear to arrive at the

listening position at the same time with-

out delay from the center speaker as

opposed to the left and right speakers.

AVR40 rev (j) 4/16/97

•AVR40 om (j).qx 9/15/98 3:47 PM Page 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR40 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info