Bedienungsanleitung Harman Kardon AVR45 (Seite 33 von 47) (Englisch)

502646

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Programming the Remote

To find out what function a particular

button has for a specific device, find

the button number on the Function List

and then look in the column for the

device you are controlling. For example,

button number 5 is the Test Tone button

for the AVR45, but it is the “Favorite”

button for many VCRs and Satellite

receivers. Button number 31 is the

Preset Tune Down button for the AVR45,

the “Reverse Skip” button for CD players

and the “Page Down” button for some

cable boxes.

Notes on Using the AVR45 Remote With

Other Devices.

• Manufacturers may use different code

sets for the same product category. For

that reason, it is important that you

check to see if the code set you have

entered operates as many controls as

possible. If it appears that only a few

functions operate, check to see if

another code set will work with more

buttons.

• When a button is pressed on the AVR45

remote, the red light under the

Device Control Selector b for

the product being operated should

flash briefly. If the Device Control

Selector flashes for some, but not all

buttons for a particular product, it

does NOT indicate a problem with the

remote, but rather that no function is

programmed for the button being

pushed.

Macro Programming

The Power button may be programmed to

send out a sequence of up to eight com-

mands when it is pushed. This enables

you to turn on a number of products,

and to have a program source turn to a

favorite channel or any other command.

To program a macro into the Power

button, follow these steps:

1. Press any of the Device Control

Selectors b and the Mute

button d at the same time until

the red light under the Device Control

Selector turns on.

2. Press the Power button c and

note that the Device Control Selector

will blink once.

3. Enter up to eight macro steps, by

pressing the Device Control button

and then the function button for each

step you wish to enter. To enter the

“Power On/Off” command during

macro programming, press the Mute

button d. DO NOT press the actual

Power Button.

4. When the eight steps have been

entered, press the Sleep button `

to enter the commands. The red light

under the Device Control Selector

will blink and then turn off.

Example: To program your TV,

Cable Box and the AVR45 to turn on

when the Power button is pressed,

first press-and-hold the AVR a

and Mute buttons d until the

red light comes on under the AVR

button. Next, press the Mute button

d to enter the Power command

for the AVR. Press the TV Device

Control Selector b to select

the TV mode, and then press the

Mute button d again, to select

TV Power. Finally, press the CBL

Device Control Selector b

followed by the Mute button d to

select Cable Power. Press the Sleep

button ` to enter the commands.

123

141615

10 11

21 22 23 24

28272625

33 34 35 36 37

43 44 45 46

4847

41403938

30 31 32

18 19 20

AVR45 om (G).Eng,Fr 4/16/99 11:41 AM Page 30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR45 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info