Bedienungsanleitung Harman Kardon AVR645 (Seite 50 von 68) (Englisch)

502558

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

50 MULTIROOM OPERATION

Multiroom Operation

Infrared Output Selection

The AVR enables you to select which IR input will

be used to feed the Full Carrier IR Output

The factory default setting is the IR signal that is

fed to the Multiroom IR Input

, but you may

select other options.

To change this setting, first make sure the

MULTI-ROOM SETUP menu is on the

screen, and then press the

⁄

Navigation

Buttons

F so that the cursor is next to

CARRIER OUT; then press the Set Button

Q. Press the

⁄

Navigation Buttons

F to select one of these options:

•

ZR10feeds the signal present at the

Multiroom IR Input

to the Full Carrier

IR Output

•

A-BUS feeds the signal carried back from an

optional A-Bus module connected to the AVR

to the Full Carrier IR Output

•

FRONT feeds the received through the front-

panel Remote Sensor Window

to the

Full Carrier IR Output

When all needed adjustments to the

MULTI-

ROOM SETUP

menu have been made, press

the

⁄

Navigation Buttons

F until

the cursor is pointing to

BACK TO MASTER

to make changes to other menus, or

press the OSD Button

E to exit the

menu system and return to normal operation.

Multiroom Operation

When operating the AVR from a remote room

location where an IR sensor link has been con-

nected to the AVR’s rear panel Multiroom IR

Input

, you may use either the Main remote

control or the ZR 10 remote buttons BC

D. Press the AVR Selector B to turn the

unit on to the last source, or any of the other

Selector buttons to turn on to a specific source.

With the remote pointing toward an IR sensor or

A-Bus module in the remote room, you may turn

on the second zone system by pressing the AVR

Selector Button B on the ZR 10 remote to

turn the system on with the last used source for

the multiroom system active, or you may press

one of the Input Selectors D or the Tuner

Selector C or Selector  to

turn the multiroom system on directly to a

specific source.

When the multiroom system is turned on, you

may use the same buttons on either remote that

would normally be used to control an AVR

function such as volume, source selection, tuner

control or the operation of an iPod docked to The

Bridge. If any of the input devices are connected

to the IR Output

or Full Carrier IR Output

, by either a hard-wire connection or through

an optional IR “blaster,” you may use the

Transport Controls P on the ZR 10 to

operate compatible Harman Kardon products.

To turn the system off from the remote room,

press the Power-Off button

A. Remember

that the AVR may be turned on or off from the

remote room regardless of the system’s operation

or status in the main room.

NOTE: When the tuner is selected as the source

for the remote zone, any change to the frequency

or preset will also change the station being

listened to in the main room, if the tuner is in use

there. Similarly, if someone in the main room

changes the station, the change will also impact

the remote room.

To activate the feed to the remote room, press

the Multiroom button

on the remote.

Next, press the Set button

When the

MULTI ON/OFF message

appears in the on-screen display and the Lower

Display Line

, press the Set Button

and then press the

⁄

Navigation Button

so that display changes to MULTI ON.

Press the Set Button

again to activate the

setting. Note that this method may be used to

turn the Multiroom system on or off even when

the AVR is in the Standby mode in the main

listening room.

IMPORTANT NOTE: When an A-BUS module is

connected, the AVR’s Multiroom system must be

turned on before the A-BUS module is able to

communicate with the AVR. Once turned on

using the instructions in the preceding

paragraph, the Multiroom system must remain

on in order for the A-BUS module to operate.

When the unit is in the Standby mode, but ready

for Multiroom or A-BUS operation, the lighting

around the Standby/On Switch

remains

blue and a

MULTI ON message appears in the

Lower Display Line

, even though the unit

is “off” in the main listening room.

When the multiroom system is turned on, the

input selected using the Multiroom Menu will be

fed to the Multiroom Output jacks

on the

rear panel as well as the A-BUS Jack

The volume will be as set in the same menu,

although it may also be adjusted using an option-

al IR sensor and the Zone II remote in the remote

location or on the optional audio power amplifier

connected to the Multiroom Output jacks

Although changes to the input source or remote

room volume will normally be made using an IR

sensor in the remote room that is connected to

the AVR, it is also possible to change those

settings from the main listening room. This is

useful for situations where some or all of the

remote rooms do not have an IR sensor, or to

take control over the remote room without

actually being in that room.

In addition to using the

MULTI-ROOM

menu, as shown on the previous page, you may

change the source or volume in the remote zone

using the remote. Press the Multiroom Button

on the remote, and when the MULTI

ON/OFF

message appears in the on-screen

display and the Lower Display Line

, press

the Set Button

and then press the

⁄

Navigation Button

to toggle past

that message to

MULTI LEVEL or

MULTI INPUT.

To change the remote room’s input source,

when

MULTI INPUT appears, press the

Set Button

, and then press the

⁄

Navigation Button

until the desired input

appears in the on-screen display and in the

Lower Display Line

. Remember that only

analog or PCM input sources may be selected for

use with the Multiroom system. Dolby Digital or

DTS sources are not available to the Multiroom

system.

To change the remote room’s volume, when

MULTI LEVEL appears, press the Set

Button

, and press the

⁄

Navigation

Button

to change the volume setting. Note

that this volume adjustment controls the level for

the output to the Multiroom Audio Outputs

and for any speakers connected to the

Surround Back/Multiroom Speaker Outputs

when the Surround Back amplifier channels

are configured for Multiroom use, as shown on

page 49. This adjustment does NOT change the

volume level for any room where an ABUS

module is used, as that setting is only adjustable

using the A-BUS module’s volume control or

built-in IR sensor.

Once the multiroom system is turned on, it will

remain on even if the AVR is placed in the

Standby mode in the main room by pressing the

Power Off Button

or the System Power

Control

on the front panel. To turn off the

multiroom system from the main listening room,

when the AVR is on press the Multiroom button

and then the Set button

. Press the

⁄

buttons

so that the Main

Information Display

or OSD will display

MULTI OFF.

Even when the AVR is turned off (to Standby

mode) and the multiroom system is turned off

too, the multiroom system may be turned on at

any time by pressing the Multiroom button

, or any of the Selector buttons

BCD in the remote room.

The

Brid

29851_AVR645_ENG 30/10/06 9:46 Side 50

Harman Kardon AVR645 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR645

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info