502637

Harman Kardon AVR7200 Seite 39

39
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
CONFIGURING THE REMOTE
CONFIGURING THE REMOTE 39
or too old, and thus not all of its commands will be in
the code library. You may fill in the codes for any button
that does not operate properly by using the learning
technique shown on page 39.
Automatic Code Entry
In addition to manual code selection using the brand
name list, it is also possible to automatically search
through all the codes that are stored in the AVR remote’s
library to see whether a device will respond even if it
is not listed among the brands that appear when you
program the remote manually. To automatically search
through the codes that are available for a specific device
type (e.g., DVD, VCR), follow these steps:
1. Turn on the power to the device you wish to
program into the AVR remote. This is important,
as in a later step you will need to see whether the
device turns off to determine whether the remote has
been programmed for the proper remote codes.
2. Press and hold the
Program Button y for
about three seconds while the message shown
in Figure 16 appears in the remote’s
LCD
Information Display c. Release the button
when the red light under the Set Button p
appears.
3. The remote’s MAIN MENU message (Figure 16)
will appear in the LCD display and the Set Button
p will remain illuminated in red. Press the Set
Button p to begin the process of selecting a
device and locating the proper remote codes.
4.
SELECT A DEVICE will appear in the LCD dis-
play (Figure 17). Press the
⁄
/
¤
Navigation
Buttons n to scroll through the list of device
categories and press the Set Button p when
the device for which you wish to set the codes
appears. For this example, we will select “TV” to
enter the codes needed to operate your TV.
5. At the next menu screen on the remote (Figure 18),
press the
⁄
Navigation Button n so that the
bottom line of the LCD display reads AUTO
(Figure 22) and then press the Set Button p
to enter the Automatic programming mode.
Figure 22
6. As instructed on the next menu screen, press
the
⁄
Navigation Button n to begin the auto-
matic code search process. Your confirmation
that the remote is sending out commands is the
movement of a square block across the top line of
the LCD display screen while the bottom line reads
PLEASE WAIT….You will also see the transmit
icon in the upper right corner of the LCD display’s
top line to remind you that the remote is working
even though you may not see anything happening
to the device being programmed.
7. It will take a few seconds for the remote to send
out the first group of commands, after which you
will see a new display in the LCD screen, as
shown in Figure 23. Following the instructions, if
the device being programmed has
not turned off,
press the
⁄
Navigation Button n again to
send another group of codes. If the device being
programmed has turned off, skip to Step 9.
Figure 23
8. By pressing the
⁄
Navigation Button n
again, the remote will send out a new set of
commands. When it pauses, follow the instructions
shown in Step 7. Depending on how many codes
are stored for a specific device type, you may have
to repeat this process as many as fifteen times.
Remember, if the device turns off, skip to Step 9.
When all the codes for the device being pro-
grammed have been tried, the instruction shown in
Figure 24 will appear. This means that the codes
for the product you are trying to program are not
in the AVR remote library and you will have to
“learn” them into the remote following the instruc-
tions shown in the next section. Press the
Set
Button p as instructed to exit the program-
ming process.
Figure 24
9. If the device being programmed does turn off
after following the instructions in Step 7, you
will need to verify the code set by pressing the
Numeric Keys k in sequence, as instructed in
Figure 23. Point the remote at the device being
programmed, and press the
“1” Button k to
see whether the device turns back on.
10. After pressing and releasing the
“1” Button k,
check to see whether the device has turned back
on. If it has, skip to Step 12. If it does not turn off,
press the
“2” Button k, or the next button in
the numeric sequence if you are repeating the
procedure, as instructed by the LCD screen in
Figure 25.
Figure 25
11. When pressing the “1” button does not turn
the device being programmed back on, repeat
the procedure by trying the remainder of the
Numeric Keys k in sequence, each time
pressing and then releasing the button to see
whether the new device turns back on. When it
does, skip to the next step. However, if you try all
10 numeric keys and find that the unit will not turn
on, you won’t be able to use this method to pro-
gram the device. Press the Clear Button j to
exit the programming process. You’ll need to follow
the Learning Commands instructions below to enter
the codes for this device into the AVR remote.
12. When pressing one of the numeric keys in Step
10 or 11 causes the device being programmed to
turn back on, follow the instructions shown in
Figure 23 and press the Set Button p within
five seconds of the device turning on. After you
press the Set button, the top line of the LCD dis-
play will read SAVING… and then the word
SAVED will flash four times in the center of the
bottom line.
13. When the codes are saved, the remote will return
to normal operation, and whenever you press
the
Input Selector Button d that was just
programmed, the codes for the new device will
be used. If no further buttons are pressed, the
remote will revert back to the default setting for
AVR commands.
Learning Commands
On occasions when the AVR remote does not contain
the codes for a particular product’s remote in its built-in
library, or when you wish to program a missing or spe-
cial function into one button of a device, the AVR
remote’s learning capability allows you to do that. To
teach commands from one product’s remote into the
AVR remote, follow these steps:
The process requires that both the device’s original
remote and the AVR remote be available. Before press-
ing any buttons on either remote, place them so that
the IR transmitter on the remote from the device to be
programmed is facing the
Infrared Lens
i
on the
AVR remote. The two remotes should be no more than
an inch apart, and there should not be any direct sun-
light or other bright light source near the remotes.
1. Press and hold the
Program Button y for
about three seconds while the message shown
in Figure 16 appears in the remote’s LCD
Information Display c. Release the button
when the red light under the Set Button p
appears.
2. The remote’s MAIN MENU message (Figure 16),
will appear in the LCD display and the Set Button
p will remain illuminated in red. Press the
⁄
Navigation Button n once so that LEARN
appears on the bottom line of the LCD screen, as
shown in Figure 26. Press the Set Button p to
POWER ON?
Y - > SET N-> 1 ~ 0
REACH END POINT
EXIT -> SET KEY
POWER OFF?
Y - > 1~ 0 N->
PROGRAM DEVICE
AUTO
AVR 7200 OM 1/27/03 4:46 PM Page 39
… 39 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Harman Kardon AVR7200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info