Bedienungsanleitung Harman Kardon AVR7200 (Seite 47 von 52) (Englisch)

502637

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

CONFIGURING THE REMOTE

CONFIGURING THE REMOTE 47

few minutes for the reset process to take place,

and the length of time will vary depending on how

much customization and programming has taken

place. Please be patient; as long as the message

appears in the display the remote is functioning

properly.

Figure 75

4. When the remote has been totally reset and

returned to the factory default condition, a

REMOTE RESET COMPLETE message will

appear (Figure 76) briefly, and then the remote will

return to normal operation.

Figure 76

Additional Notes on Configuring and Operating

the Remote:

• When the remote is being programmed, it will auto-

matically time-out if no button is pressed within a

thirty-second period. The message shown in Figure

78 will appear briefly, and the remote will then exit

the feature being programmed and any data entered

will be lost.

Figure 77

• The programming or configuration process may

also be stopped at any time by pressing the Clear

Button

. The message shown in Figure 77

will appear, the data entered in the current process

will be lost and the remote will return to normal

operation. Any process that was underway when

the button will be pressed must be restarted.

• Extensive use of the programming, learning and con-

figuration functions of the remote may consume sig-

nificantly more battery power than normal remote

operation. While the batteries should last for four to

six months in normal operation, you may find that

they need to be changed sooner after the remote is

programmed for the first time.

• When the batteries approach a level below which the

remote will not function, the remote’s LCD screen will

display a

LOW BATTERY warning as shown in

Figure 78. We strongly recommend replacing the

batteries as soon as this message appears to avoid

the loss of programming and configuration settings.

These settings are

not lost when the batteries are

changed quickly.

Figure 78

• The remote has a built-in backlight that may be

activated by pressing the Light Button

. This

button is made from a special “glow” material so

that it is easier to find in dark rooms. This glow

feature does not consume any electricity, but the

glow will fade when the remote is kept in a dark

location for an extended period of time. The “glow”

feature may be restored by placing the remote in

normal room light for a few hours.

• The remote’s backlight will remain lit for approxi-

mately five seconds after the

Light Button

pressed, and it will stay lit for another five seconds if

any key is pressed while the backlight is on. You may

keep the backlight lit by holding the Light Button, but

extensive use of the backlight will reduce battery life.

• The LCD display will remain on for ten seconds

after a key is pressed and then turn off to conserve

battery life.

• When any button is held for more than thirty

seconds the LCD will turn off and the remote will

stop transmitting the codes to conserve battery life.

AVR

LOW BATTERY

TIME OUT OR

CLR KEY PRESSED

REMOTE RESET

COMPLETE

RESETTING...

AVR 7200 OM 1/27/03 4:47 PM Page 47

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR7200 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info