12 VIDEO AND SYSTEM CONNECTIONS
VIDEO AND SYSTEM CONNECTIONS
A Amp TConnect this jack to the “T
jack of an optional, external power amplifier that is
equipped for remote turn-on via a 6-volt signal. When
this connection is used, the
send a low-voltage signal that turns on the amp when the
A
A
A
B Multiroom IR Input: Connect the output of an
sensor in a remote room to this jack to operate the
A
C Remote IR Output: This connection permits the
IR sensor in the receiver to serve other remote-con-
trolled devices Connect this jack to the
Harman Kardon (or other compatible) equipment.
D Remote IR Input: If the A
IR sensor is blocked due to cabinet doors or other
obstructions an external IR sensor may be used.
Connect the output of the sensor to this jack.
E Component Video Monitor Outputs: Connect
these outputs to the component video inputs of a
video projector or monitor When a source connected
to one of the Component Video FGH is
selected, the signal will be sent to these jacks
F DVD Component Video Inputs: Connect the
component video outputs of a DVD player or any
other video source equipped with
component video outputs to these jacks The factor
default is for these jacks to be linked to the DVD
Audio Inputs © and the Coaxial 1 Digital
Input †, but you may change the setting at any time
through the IN/OUT SETUP menu. See page
23 for more information on configuring the compo-
nent video inputs
G Component Video 2 Inputs: These inputs may
be used with any video source device equipped with
analog The
factory default is for these jacks to be linked to the
Video 2 through
the setting at any time through the IN/OUT
SETUP menu. See page 23 for more information
on configuring the component video inputs
H Component These inputs may
be used with any video source device equipped with
analog The
factory default is for these jacks to be linked to the
Video 1 input, but you may change the setting at any
time through the IN/OUT SETUP menu. See
page 23 for more information on configuring the
component video inputs
I DVD Video The default use for these
inputs is the connection to the composite and/or S-
Video output of a DVD player but they may be used
with a different video source if desired.
J Video Monitor Outputs: When using an analog
video display that has only standard composite and
S-Video inputs connect the output of these jacks
(depending on which types of video are used by your
source devices) to the matching inputs on your televi-
sion or video display When using a or
HDTV display that is compatible with 480P or higher
inputs you do not need to make these connections as
all incoming video will be up-scaled to 480P and sent
through the Component E
with the OSD messages
K Video 4 Connect the composite or
S-Video jacks of a video device to these jacks The
A
the default for this input, but you may connect any
video source such as a personal
video recorder or other device to these inputs (See
page 23 for more information on configuring an input
for various source options
L A-BUS Connectors:
Connect these jacks to an
optional
A-BUS
®
-certified remote modules to extend the
multiroom capabilities of your See page 20
for more information on A-BUS
M Video 1
Connect the composite
S-Video RECORD/IN jacks of a video recording device
such as a
to these jacks
N Video 1
Connect the composite or
S-Video PLA
such as a
to these jacks The A
VCR as the default for this input, but you may connect
any video source such as a
box, personal video recorder or other device to these
inputs (See page 23 for more information on configuring
an input for various source options
O Multiroom Video
Connect these jacks to
the cabling and/or an optional, external video distribution
amplifier that delivers the video source selected for the
multizone distribution to the remote rooms
P AC Power Cord Jack: Connect the AC power
cord to this jack when the installation is complete
T use only the power cord
supplied with the unit. If a replacement is required,
it must be of the same type and capacity
Q UnsThis outlet may be used
to power any
sumption does not exceed 100 watts The power
will remain available at this outlet as long as the
A
regardless of whether the
R Switched AC These outlets may be used
to power
and off when the The total
power consumption of all devices connected to the
two outlets may not exceed 100 watts
S RS-232 Port: This jack may be used to control
the
control link to a compatible computer or programmable
remote control system. Due to the complexity of
programming RS-232 commands we strongly
recommend that connections to this port for control
purposes be made by a trained and qualified
technician. This jack may also link to a compatible
computer to upgrade the software and operating sys-
tem of the
available
T Video 2 Connect the composite or S-
Video PLA
as a
these jacks The
as the default for this input, but you may connect any
video source such as a
personal video recorder or other device to these inputs
(See page 23 for more information on configuring an
input for various source options
U Video 2 Connect the composite or
S-Video RECORD/IN jacks of a video recording device
such as a
to these jacks
V Video 3 Connect the composite
or S-Video jacks of a video device to these jacks The
A
the default for this input, but you may connect any
video source such as a personal
video recorder or other device to these inputs
page 23 for more information on configuring an input
for various source options
W FM Antenna: Connect the supplied indoor or an
optional external FM antenna to this terminal.
X AM Antenna: Connect the AM loop antenna sup-
plied with the receiver to these ter
AM antenna is used, make connections to th AM and
GND terminals in accordance with the instructions
supplied with the antenna.
AVR7300(120v)-OM 6/14/04 9:15 AM Page 12
