Bedienungsanleitung Harman Kardon AVR7300 (Seite 40 von 60) (Englisch)

502638

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

To enter a station into the memory, first tune the sta-

tion using the steps outlined above. Then:

1. Press the Memory Button on the remote;

the station’s frequency will flash.

2. Within five seconds, press the Numeric Keys k

corresponding to the memory location where you

wish to store this station’s frequency. Once entered,

the preset number will appear in the Upper

Display Line #.

3. Repeat the process after tuning any additional

stations to be preset.

Recalling Preset Stations

• To manually select a station previously entered in

the preset memory, press the Numeric Keys k

for the desired station’s memory location.

• To manually scroll through the list of preset stations,

press the Preset Stations Selector Button

6v on the front panel or remote.

Recording

In normal operation, the audio or video source

selected for listening through the AVR 7300 is sent to

the record outputs. This means that any program you

are watching or listening to may be recorded simply

by placing machines connected to the outputs for

Tape Outputs ∂ or Video 1/Video 2 Outputs

π∆ in the record mode.

When a digital audio recorder is connected to the

Digital Audio Outputs œß , you are able

to record the digital signal using a CD-R, MiniDisc or

other digital recording system.

NOTES:

• The digital outputs are active only when a digital sig-

nal is present, and they do not convert an analog

input to a digital signal, or change the format of the

digital signal. In addition, the digital recorder must

be compatible with the output signal. For example,

the PCM digital input from a CD player may be

recorded on a CD-R or MiniDisc, but Dolby Digital

or DTS signals may not.

• The Front-Panel Video 5 jacks may be con-

figured for use as an output, allowing connection to

a recorder, when the steps shown in the section

below are followed.

• Please obey the copyright restrictions on any mate-

rial you copy. Unauthorized duplication of copyright-

ed materials is prohibited by law.

Front-Panel Connections

In addition to the rear-panel digital and analog outputs,

the AVR 7300 offers Harman Kardon’s exclusive con-

figurable front-panel output-jack feature. For easy con-

nection of portable devices, you may switch the front-

panel Video 5 Jacks from an input to an output

by following these steps:

1. Press the OSD Button U to view the

MASTER MENU (Figure 1).

2. Press the Set Button q to enter the

IN/OUT SETUP menu (Figure 2).

3. Press the

Navigation Button o so that the

on-screen ➔

cursor is next to VIDEO 5.

4. Press the Set Button q and then press the

‹

›

Navigation Button o so that the word

OUT is highlighted.

5. Press the Set Button q to enter the change.

6. Press the OSD Button U to exit the menus and

return to normal operation.

Once the setting is made, the Input/Output Status

Indicator will turn red, indicating that the jacks

are now an output, instead of in the default setting as

an input. Once changed to an output, the setting will

remain as long as the AVR 7300 is turned on, unless

the setting is changed in the OSD menu system, as

described above. However, once the AVR 7300 is

turned off, the setting is cancelled. When the unit is

turned on again, the front-panel jacks will return to

their normal default setting as an input. If you wish

to use the jacks as an output at a future time, the

setting must be changed again using the OSD menu

system, as described above.

Output Level Trim Adjustment

Normal output level adjustment for the AVR 7300 is

established using the test tone, as outlined on pages

29–30. In some cases, however, it may be desirable to

adjust the output levels using program material such as

a test disc, or a selection you are familiar with.

Additionally, the output level for the subwoofer can only

be adjusted using this procedure.

To adjust the output levels using program material, first

set the reference volume for the front left and front right

channels using the Volume Control )r

If you are using a disc with test signals or an external

signal generator as the source used when the output

levels are being trimmed, you may use the remote as

an SPL meter to guide you to the correct level set-

tings. To use the EzSet remote as an SPL meter, follow

the instructions on page 29.

Once the reference level has been set, press the

Channel Select Button n and FRONT L

LEVEL will appear in the Lower Display Line

$. To change the level, first press the Set Button

q, and then use the

⁄

Navigation Button

o to raise or lower the level. DO NOT use the vol-

ume control, as this will alter the reference setting.

Once the change has been made, press the Set

Button q and then press the

⁄

Navigation

Button o to select the next output-channel location

that you wish to adjust. To adjust the subwoofer level,

press the

⁄

Navigation Button o until

WOOFER LEVEL appears in the Lower Display

Line $ or on-screen display.

Repeat the procedure as needed until all channels

requiring adjustment have been set. When all adjust-

ments have been made and no further adjustments

are made for five seconds, the AVR 7300 will return to

normal operation.

The channel output for any input may also be adjusted

using the full-OSD on-screen menu system. First, set

the volume to a comfortable listening level using the

Volume Control

. Then, press the OSD

Button U to bring up the MASTER MENU

(Fig. 1). Press the

Navigation Button o until

the on-screen ➔ cursor is next to the CHANNEL

ADJUST line. Press the Set Button q to

activate the CHANNEL ADJUST menu (Fig. 13).

Once the menu appears on your video screen, first

use the

⁄

Navigation Button o to move the

on-screen ➔ cursor so that it is next to the TEST

TONE line. Press the

‹

›

Navigation Button o

so that OFF is highlighted. This will turn off the test

tone and allow you to use your external test disc or

other source material as the reference. Then, use the

⁄

Navigation Button o to select the chan-

nels to be adjusted. At each channel position, use the

‹

›

Navigation Button o to change the output

level. Remember, the goal is to have the output level

at each channel be equal when heard at the listening

position.

If you wish to reset all the levels to their original factory

default of 0dB offset, press the

⁄

Navigation

Button o so that the on-screen cursor is next to

the CHANNEL RESET line and press the

‹

›

Navigation Button o so that the word ON is

highlighted. After the levels are reset, resume the

procedure outlined above to reset the levels to the

desired settings. When all adjustments are done, press

the

⁄

Navigation Button o to move the on-

screen ➔ cursor so that it is next to BACK TO

MASTER MENU and then press the Set Button

q if you wish to go back to the main menu to

OPERATION

40 OPERATION

OPERATION

AVR7300(120v)-OM 6/14/04 9:15 AM Page 40

Harman Kardon AVR7300 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info