Bedienungsanleitung Harman Kardon AVR85 (Seite 21 von 40) (Englisch)

502655

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

System Configuration

AVR85 120 rev (g) 6/14/97

System Setup

Once the speakers have been placed in

the room and connected, the final step

is to enter the configuration information

and balance the speaker output levels.

Before proceeding further this is a good

time to review the installation section

of the manual to make certain that all

connections are properly made.

1. Plug the unit into an AC wall outlet

and press the Power button on either

the front panel 1 or the remote c.

Note that the ring surrounding the front

panel switch will turn green, and the

front panel display will illuminate.

2. Install the supplied AAA batteries in

the remote as shown on page 15.

3. Turn on the TV connected to the

receiver. Select the appropriate video

input on the TV.

Note: Although the unit will switch

S-Video signals, the on-screen menus

control system is NOT visible on the

S-Video output.

4. Press the Select button j on the

remote to bring the MAIN MENU up on

your video screen.

5. Press the ¤ button four times until

the on-screen cursor

is pointing to

SET UP MENU (see figure #1).

6. Press Select j to move to the

next screen, SET UP MENU 1 (see

figure #2).

7. SET UP MENU 1 enters the

information that tells the AVR85 which

type of front and surround speakers

will be used. In turn, these settings will

determine which speakers receive low

frequency (bass) information. For the

purposes of establishing proper bass

reproduction, use the LARGE settings if

the speaker being used at any position

is a traditional full-range loudspeaker

that is capable of reproducing sounds

below 100Hz. Use the SMALL setting for

smaller, frequency-limited satellite

speakers that are not able to reproduce

sounds below 100Hz. Note that when

“small” speakers are used it is advisable

to install a separate subwoofer.

8. Enter the information for the FRONT

CH. speaker by using the ‹ or › buttons

i on the remote to select the type of

front channel speaker that will be used.

Press the buttons so that LARGE or

SMALL is highlighted to match the

speaker type you will use as described in

item #7 above. The LARGE setting sends a

full-range output to the front left/right

speakers, while the SMALL setting sends

low-frequency sounds to the subwoofer

output. When the selection has been

made, press the ¤ button once so that

the on-screen cursor

is pointing

to the SURROUND CH. line of the

display.

INPUT SELECTOR

SURROUND MODE

TEST TONE

MULTI ROOM SEL:OFF

SET UP MENU

SLEEP TIMER:OFF

MENU OFF

MAIN MENU

Figure 1

SPEAKER SETTING

FRONT CH

LARGE

SMALL

SURROUND CH

LARGE

SMALL

NONE

GO TO SET UP MENU 2

RETURN TO MAIN MENU

SETUP MENU 1

Figure 2

CENTER CH

LARGE

SMALL

NONE

SUBWOOFER ON

OFF

GO TO SET UP MENU 3

RETURN TO MAIN MENU

SETUP MENU 2

Figure 3

LFE LEVEL CONTROL

OFF:0dB - 10dB

NIGHT MODE :OFF ON

SETUP LOCK :LOCK

UNLOCK

GO TO SET UP MENU 4

RETURN TO MAIN MENU

SETUP MENU 3

Figure 4

OFF ON

FRONT L

TEST TONE

0 dB

Figure 5

AVR85 om (g) 9/16/98 11:21 AM Page 18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR85 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info