Bedienungsanleitung Harman Kardon BDS 700 Systeem (Seite 7 von 38) (Englisch)

658948

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

BDS

PL0004-01001

ENGLISH

Subwoofer Controls and Connections

Phase Switch: This switch determines whether the subwoofer driver’s piston-like action

moves in and out in phase with the satellite speakers. If the subwoofer were to play out of

phase with the satellite speakers, the sound waves produced by the subwoofer could be

cancelled out, reducing bass performance and sonic impact. This phenomenon depends in

part on the relative placement of all the speakers in the room.

Although in most cases the Phase switch should be left in the “Normal” position, there is no

absolutely correct setting for it. When the subwoofer is properly in phase with the satellite

speakers, the sound will be clearer and have maximum impact. It will make percussive

sounds like drums, piano and plucked strings sound more lifelike. The best way to set the

Phase switch is to listen to music that you are familiar with and set the switch in the position

that gives drums and other percussive sounds maximum impact.

Bass-Boost Switch: Set this switch to “On” to enhance the subwoofer’s low-frequency

performance. Set this switch to “Off” for normal low-frequency performance.

Power-On Mode Switch: When this switch is set in the “Auto” position and when the

Power switch is set to “On,” the subwoofer will automatically turn itself on when it receives

an audio signal. It will enter the Standby mode if it receives no audio signal for 20 minutes.

When the Power-On Mode switch is set in the “On” position, the subwoofer will remain on

whether or not it is receiving an audio signal.

An LED on the subwoofer’s top panel indicates whether the subwoofer is in the On or Standby

mode:

When the LED glows

•

white, the subwoofer is turned on.

When the LED is not lit up, the subwoofer is in Standby mode.

•

When the Main Power Switch is set to Off, the LED will not light up, no matter what setting

the Power-On Mode switch is in.

Subwoofer Level Control: Use this control to adjust the subwoofer’s volume. Turn

clockwise to increase the volume; turn counterclockwise to decrease the volume.

External Trigger Input Connector: NOTE: This connector is NOT used with the

BDS receiver. If you connect the subwoofer to a different component that has a voltage

trigger output connection, connect the External Trigger Input to the trigger output of the

other compatible component. Whenever the subwoofer detects a trigger signal between 3V

and 30V (AC or DC), the subwoofer’s amplifier will turn on. The subwoofer’s amplifier will

turn off after the trigger signal ceases, even when the Power-On Mode switch is in the “Auto”

position.

Line-Level In LFE Connector: Use the supplied mono RCA audio cable (with the purple

connectors) to connect the Line-Level In LFE connector to the BDS receiver’s Subwoofer

output.

Line-Level In L/R Connectors: NOTE: These connectors are NOT used with the

BDS receiver. If you connect the subwoofer to a different unit that does not have a dedicated,

low-pass-filtered subwoofer output, use these connectors.

If the unit has a separate subwoofer output, use the supplied mono RCA audio cable to

•

connect the unit’s subwoofer output to either one of the subwoofer’s Line-Level In L/R

connectors.

If your unit does not have a separate subwoofer output, use two Y-adapters (not

•

supplied). Connect one adapter’s single end to the unit’s preamp output for that

channel. Connect one of this adapter’s dual ends to the main amp input for that channel,

and connect the adapter’s other dual end to one of the subwoofer’s Line-Level In L/R

connectors. Repeat this process with the other Y-adapter, preamp channel, main amp

input and subwoofer’s Line-Level In L/R connector.

Main Power Switch: Set this switch in the On position to turn the subwoofer on. The

subwoofer will then either be on or in Standby mode, depending on the setting of the

subwoofer’s Power-On Mode switch.

Power Cord: After you have made and verified all subwoofer and speaker connections

described in this manual, plug the Power cord into an active, unswitched electrical outlet for

proper operation of the subwoofer. DO NOT plug this cord into the accessory outlets found in

some audio components.

Subwoofer Controls and Connections

Phase Switch

Bass-Boost Switch

Power-On Mode Switch

Subwoofer Level Control

External Trigger Input Connector

Line-Level In LFE Connector

Line-Level In L/R Connector

Power Switch

Power Cord

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon BDS 700 Systeem Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon BDS 700 Systeem

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info