Bedienungsanleitung Harman Kardon BDS 776 - SET (Seite 7 von 34) (Englisch)

537906

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

ENglIsh

Receiver Rear-Panel Connections

NOTE: See the Connections section, on page 10, for detailed information about

making connections.

Main Power switch: This mechanical switch turns the BDS receiver’s power supply

on or off. After you have made and veriﬁed all connections (see the Connections

section, on page 10), set this switch to the “On” position. During normal use you will

usually leave this switch set to On; it cannot be turned on or off using the remote

control. To conserve energy when you’re not going to be using the receiver for an

extended period of time, set this switch to “Off.”

AC Power connector: After you have made and veriﬁed all other connections, plug

the supplied AC power cord into this input and into an unswitched AC outlet.

Speaker connectors: Use the speaker wires supplied with the speakers to connect

the satellite and center speakers to the proper terminals.

• The BDS 570 receiver (shown) has connections for ﬁve speakers: front left, front

right, surround left, surround right and center.

• The BDS 270 receiver (not shown) has connections for two speakers: front left

and front right.

See Connections, on page 10, for more information.

Fan vents: These vents are used by the receiver’s fan to cool the unit. Maintain a

clearance of at least three inches (75mm) from the nearest surface to avoid overheating

the unit. It is normal for the fan to remain off at most normal volume levels. An automatic

temperature sensor turns the fan on only when it is needed.

IMPORTANT NOTE: Never block the fan vents. Doing so could allow the BDS receiver

to overheat to dangerous levels.

Optical Digital Input connectors: Connect the optical digital output of an audio-

only source component here. The signal may be a Dolby

Digital bitstream, a DTS

bitstream or a standard PCM digital-audio bitstream.

NOTE: Use only one type of digital connection for each source component.

Coaxial Digital Input connector: Connect the coaxial digital output of an audio-

only source component here. The signal may be a Dolby Digital bitstream, a DTS

bitstream or a standard PCM digital-audio bitstream.

NOTE: Use only one type of digital connection for each source component.

Component Video Input connector: If you have a video source device that has a

component video connector (and does not have an HDMI connector), use the component

video connector. You will also need to make an audio connection from the device to the

BDS receiver’s Aux In 1 connectors. See Connections, on page 11, for more information.

Subwoofer Output connector: Use the supplied mono RCA audio cable (with the

purple connectors) to connect this jack to the subwoofer’s Line-Level In LFE jack.

See Connecting a Powered Subwoofer, on page 10, for more details about making

connections.

Subwoofer Trigger connector: This connector provides 12V DC whenever the receiver

is on. It can be used to turn on and off other devices such as a powered subwoofer.

Remote IR Input connector: When the IR sensor on the front panel is blocked (such as

when the receiver is installed inside a cabinet), connect an optional IR receiver to the

Remote IR Input connector.

BD-Live connector: To be able to use the BD-Live feature, connect this port to

your local area network (LAN) using a Cat. 5/Cat. 5E network cable. See BD-Live

Interactivity, on page 22, for details.

Analog Audio Input connectors: Use these connectors to connect to an audio-

only source component (such as a tape deck). Do not connect a turntable to these

connectors without a phono preamp.

HDMI Input connectors (HDMI ver. 1.4a with 3-D): You can connect up to three

additional source devices that have HDMI connectors to the BDS receiver. The HDMI

connection transmits digital audio and video signals between devices, so you do not

have to make any additional audio connections for devices you connect via an HDMI

connector. The BDS receiver will pass 3-D video signals from 3-D capable HDMI source

devices to the TV via the HDMI Monitor Out connector. See Connecting Your HDMI Source

Devices, on page 11, for more information.

The Bridge IIIP connector: Connect The Bridge IIIP iPod/iPhone dock (available

separately) to this terminal.

Analog Audio Output connector: Connect this output to an analog recorder’s input

connector. You can record any signal from the receiver’s Analog Audio Input connectors.

HDMI Monitor Out connector (HDMI ver. 1.4a with 3-D): Connect the BDS

receiver’s HDMI output to your TV’s HDMI input. Since the HDMI cable transmits

both video and audio to the TV, we recommend that you set the receiver’s HDMI

audio output to Off in the receiver’s Audio menu to take full advantage of your BDS

receiver’s superior audio performance. The receiver’s HDMI Monitor Out connection

contains an Audio Return Channel that carries a digital audio signal from your TV or

video display back to the receiver. It allows you to listen to HDMI devices that are

connected directly to your TV (such as an Internet connection) without making an

additional connection from the device to the BDS receiver.

IMPORTANT: Your BDS receiver is in compliance with HDCP (High-Deﬁnition

Copy Protection). Your TV must also be HDCP-compliant to be used with the BDS

receiver’s HDMI output. For best results, we do not recommend HDMI connections

in excess of ten feet (about 3 meters) without a repeater. If your TV has a DVI input,

you may use an optional HDMI-to-DVI cable or adapter for the video connection to

the TV. (The DVI connection is video-only.)

FM Antenna connector: Connect the supplied FM antenna to this terminal.

BDS 270/BDS 570

Harman Kardon BDS 776 - SET Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon BDS 776 - SET

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info