Bedienungsanleitung Harman Kardon BDS 877 (Seite 7 von 38) (Englisch)

531041

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

ENGLISH

BDS Receiver Rear-Panel Connections

NOTE: See the Connections section, on page

, for detailed information about

making connections.

Main Power switch: This mechanical switch turns the BDS receiver’s power supply

on or off. After you have made and veriﬁed all connections (see the Connections

section, on page

), set this switch to the “On” position. During normal use you will

usually leave this switch set to On; it cannot be turned on or off using the remote

control. To conserve energy when you’re not going to be using the receiver for an

extended period of time, set this switch to “Off.”

Fan vents: These vents are used by the receiver’s fan to cool the unit. Maintain a

clearance of at least three inches (75mm) from the nearest surface to avoid overheating

the unit.

IMPORTANT NOTE: Never block the fan vents. Doing so could allow the BDS receiver

to overheat to dangerous levels.

Speaker connectors: Use the speaker wires supplied with the speakers to connect

the satellite and center speakers to the proper terminals.

• BDS 575 and BDS 577 receivers (shown) have connections for ﬁve speakers: front

left, front right, surround left, surround right and center.

• BDS 275 and BDS 277 receivers (not shown) have connections for two speakers:

front left and front right.

See Connections, on page

, for more information.

Subwoofer Trigger connector: This connector provides 12V DC whenever the receiver

is on. It can be used to turn on and off other devices such as a powered subwoofer.

Remote IR Input connector: When the IR sensor on the front panel is blocked (such as

when the receiver is installed inside a cabinet), connect an optional IR receiver to the

Remote IR Input connector.

Coaxial Digital Input connector: Connect the coaxial digital output of an audio-

only source component here. The signal may be a Dolby

Digital bitstream, a DTS

bitstream or a standard PCM digital-audio bitstream.

NOTE: Use only one type of digital connection for each source component.

Subwoofer Output connector: Use a mono RCA audio cable to connect this jack

to a powered subwoofer’s line-level input or LFE jack. See Connecting a Powered

Subwoofer, on page

, for more details about making connections.

Analog Audio Input connectors: Use these connectors to connect to an audio-only

source devices (such as a tape deck). Do not connect a turntable to these connectors

without a phono preamp.

FM Antenna connector: Connect the supplied FM antenna to this terminal.

Optical Digital Input connectors: Connect the optical digital output of an audio-

only source component here. The signal may be a Dolby Digital bitstream, a DTS

bitstream or a standard PCM digital-audio bitstream.

NOTE: Use only one type of digital connection for each source component.

Network connector: Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the BDS

receiver’s Network connector to your home network to enjoy streaming content and

content from DLNA

-compatible devices that are joined to the network. See Connect

to Your Home Network, on page 12, for more information.

HDMI

Monitor Out connector: Connect the BDS receiver’s HDMI output to your

TV’s HDMI input. Since the HDMI cable transmits both video and audio to the TV,

we recommend that you set the BDS receiver’s HDMI audio output to Off in the

receiver’s Audio menu to take full advantage of your BDS receiver’s superior audio

performance. If your TV is 3D capable you can watch 3D content in 3D either from

the BDS receiver’s built-in disc player or from other 3D-capable source devices

connected to the BDS receiver’s HDMI Input connectors (see below).

The receiver’s HDMI Monitor Out connection also contains an Audio Return Channel

that carries a digital audio signal from your TV or video display back to the receiver.

It allows you to listen to HDMI devices that are connected directly to your TV (such

as an Internet connection) without making an additional connection from the device

to the BDS receiver. NOTE: You must enable your TV’s Audio Return channel output.

Consult your TV’s instruction manual for information.

HDMI Input connectors: You can connect up to three additional source devices that

have HDMI connectors to the BDS receiver. The HDMI connection transmits digital audio

and video signals between devices, so you do not have to make any additional audio

connections for devices you connect via an HDMI connector. The BDS receiver will pass

3D video signals from 3D capable HDMI source devices to the TV via the HDMI Monitor Out

connector. See Connecting Your HDMI Source Devices, on page 11, for more information.

NOTE: If you have an Apple TV, connect its HDMI output to the BDS receiver’s HDMI 3

input. When HDMI 3 is the selected source you can use the BDS remote to control various

Apple TV functions. See Controlling an Apple TV, on page 15 for more information.

Component Video Input connector: If you have a video source device that has a

component video connector (and does not have an HDMI connector), use the component

video connector. You will also need to make an audio connection from the device to one

of the BDS receiver’s audio input connectors. See Connections, on page 10, for more

information.

AC Power connector: After you have made and veriﬁed all other connections, plug

the supplied AC power cord into this input and into an unswitched AC outlet.

Harman Kardon BDS 877 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon BDS 877

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info