Bedienungsanleitung Harman Kardon BDS 880 (Seite 12 von 32) (Englisch)

531042

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

BDS 280/580

Preparing the Remote Control

NOTE: iOS version 5 or higher is required for iOS Wi-Fi sharing.

1. Select Configure Wi-Fi by iOS from the Setup Wi-Fi list.

A pop-up will be displayed on your iOS device.

2. Select Allow to confirm that you want to share your Wi-Fi settings.

3. The connection should now be established automatically.

Check the status on your TV for confirmation

WPS PBC (Push Button Control)

1. Select WPS PBC from the Setup Wi-Fi list.

2. Press the WPS button on the rear panel of the BDS.

3. Next go to your wireless router and press its WPS button.

4. The connection should now be established automatically

Check the status on your TV for confirmation.

WPS PIN

1. Select WPS PIN from the Setup Wi-Fi list.

A PIN code is displayed on the screen.

2. Enter this same PIN on your wireless router’s internal web page

to connect. See your router’s user manual for more details.

Preparing the Remote Control

Installing the Batteries

Your system’s remote control uses three AAA batteries (supplied). Insert the batteries as

shown in the illustration, making sure to observe the correct polarity.

Using the Remote Control

When using the remote control, remember to aim it towards the system’s front panel.

Make sure that no objects, such as furniture, block the remote’s view of the system.

Bright lights, fluorescent lights, and plasma-video displays may interfere with the

function of the remote.

• The remote control has a range of about 20 feet (6.1m), depending on the

lighting conditions.

• You can use the remote at an angle of up to 30° to either side of the BDS

system.

If the remote seems to operate intermittently, or if pressing a button on the remote

does not cause the remote control backlights to light up, make sure that the batteries

are inserted correctly. If the remote still operates intermittently, replace all three

batteries with new ones.

Programming the Remote Control

In addition to controlling the BDS system, you can program the unit’s remote to

control one auxiliary (aux) component. The remote is also capable of learning codes

directly from other remotes. This ability allows you to combine learned commands

with programmed codes, making the remote capable of controlling more than one

aux component. Typical aux components would be your TV, a satellite system or a cable

system. The remote will control the aux component(s) only when the aux source button

has been pressed. Pressing any other source button will put the remote back into the

normal BDS system control mode.

To Program the Remote to Control an Aux Component:

1. Check the set-up codes for the component type (for example,

TV or cable box) and its brand in the Aux Component

Remote-Control Code List, starting on page 23.

Wireless router

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon BDS 880 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon BDS 880

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info