Bedienungsanleitung Harman Kardon HD990 (Seite 11 von 16) (Englisch)

502536

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

HD 990

Programmed Play Operation

Programmed Play

The HD 990’s advanced programming capability enables you to select certain tracks, to

preset the order in which these tracks play, and to clear speciﬁc programmed tracks after

the program was made.

Programmed play allows you to program up to 32 tracks into the HD 990’s memory. To

begin programming the CD player, make sure that the unit is in Stop mode, then press

the

Program

button d. The

Program

indicator will light in the

Information Display

1, the number 001 will blink below the Program indicator, showing the track number

selected, and PROG-01: 001 will appear in the Information Display, replacing the

track time. This indicates that you are about to program the ﬁrst track.

You may now begin to enter the tracks in the order in which you wish to have them

play. To select a track on the disc, press the

Numeric

buttons c corresponding to the

desired track. Be certain to enter the second and/or third number of two- or three-digit

numbers within two seconds after the ﬁrst number was entered. You may also use the

Skip

buttons 78h to select a track. When the track is selected, press the

Program

button d. Note that the program-step indication on the right side of the

Information

Display

will change to PROG-02: 001.

You may now select another track for the next program step, following the instructions

shown above. When the track is selected, press the

Program

button d again. Repeat

this procedure for each program step until you have completed the desired programming.

Press the

Stop

button 6k once to complete a program sequence, or press

Play

4jto begin immediate play of a program sequence. If the maximum of 99 program

steps is reached, the program-step indication at the right side of the Information Display

will go out, and the disc and track that have been programmed as the ﬁrst program step

will be shown.

Once a program list has been entered, press the

Play

button 4jto begin listening

to the sequence. After the entire program has been played, the CD player will stop. As

long as the

Stop

button 6khas not been pressed twice and the

Program

indicator

remains lit, you may repeat the programmed-play sequence again by pressing the

Play

button 4j.

Editing a Program

A program can be edited even after it was completed by pressing the

Stop

button 6 k

once: Each time you press the

Program

button d the track number and program step

number will be displayed in the programmed order, but with steady track numbers (not

blinking) in contrast to the programming mode. As soon as the track number starts

blinking (this will take 1 second), the appropriate program step number shown at the left

side is not programmed yet; now you can change the track number with the

Skip

buttons

78hor the

Numeric

buttons c as described above and add it to the program

list by pressing the Program button d.

Pressing the

Stop

button 6k twice will return to normal mode and the

Program

indicator will go out, but the program will stay in memory and can be recalled easily by

pressing the

Program

button. But pressing the

Clear

button e (see below) or opening

the disc drawer by pressing

Open/Close

3p, will erase the program information

from the unit’s memory.

Checking Program Contents

To check the contents of a program while the unit is stopped at ﬁrst note that the

Program

indicator is lit (otherwise press

Program

) and the program step indication PROG-01:

is not lit (otherwise press

Stop

once). Each time the

Check

button o is pressed now,

the Information Display will step through each of the programmed tracks. To cancel the

check mode press the

Stop

button twice.

Clearing Programs

To clear a single track from the program list, press the

Program

button d until the

track to be deleted from the program sequence appears in the

Information Display

When the track number appears, press the

Clear button

e once, the track selected

will be deleted and the track number will be replaced by the next programmed one. Now

you can delete that track too with the Clear button or press the

Stop

button 6k and

again the

Program

d button to select lower track numbers to be deleted.

When the unit is stopped and the program step indication PROG-01: 001 is not

lit (otherwise press

Stop

once), but the

Program

indicator is still lit (otherwise press

Program

d) you may clear the entire contents of a program by pressing the

Clear

button e.

Important Note

: When you’ve pressed the

Program

button d (once or several times)

and the track number on the right starts blinking, the appropriate program step number

(e.g. PROG-02:008) shown at the left display side is not programmed yet. Do

not continue to press the Program button now, otherwise the track selected will be

memorized too. If you´re in doubt, press

Stop

button 6k and start the procedure

again with

Program

Important Note

: Tracks programmed as described above can be played repeatedly too.

When you press

Repeat

f once after a program is created (the

Program

indicator must

be lit, otherwise press

Program

) and the program is played, the Repeat 1 indicator will

light and the track currently playing will be repeated continuously. If

Repeat

is pressed

twice, “Repeat All” will be displayed, all programmed tracks will be played subsequently

and the sequence will be repeated continuously until the Stop button is pressed.

Harman Kardon HD990 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon HD990

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info