Bedienungsanleitung Harman Kardon HKTS 2 MkII (Seite 5 von 16) (Englisch)

769909

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

REAR PANEL CONNECTIONS 5

Rear Panel Connections



Phase Switch: This switch determines

whether the subwoofer’s piston-like action

moves in and out in phase with the main speak-

ers. If the speakers were to play out of phase,

the sound waves produced by the subwoofer

would be cancelled out, reducing bass response.

This phenomenon depends in part on the rela-

tive placement of the speakers in the room. In

most cases, the Phase Switch



should be

left in the

NORMAL

position. However, it does

no harm to experiment with the Phase Switch



, and you may leave it in the position that

maximizes bass response.



Line-Level Subwoofer (SUB) Input: Con-

nect the subwoofer output of a receiver with

digital surround sound decoding, such as Dolby*

Digital or DTS®, to this input. This input bypasses

the subwoofer’s internal crossover circuitry, and

should only be used with a filtered signal. If your

receiver does not have digital decoding, you

should use the Line-Level Full-Range Inputs



instead.



Line-Level Full-Range Inputs: Connect

the line-level subwoofer output or preamp out-

put(s) of your receiver or amplifier to these

inputs. If your receiver does not have a separate

subwoofer output, use a Y-adapter (not supplied)

to bridge the receiver’s preamp output to the

main amp input for that channel, and connect

the long end of the adapter to the correspon-

ding line-level input on the subwoofer. If your

receiver has only a single subwoofer output, you

may connect it to either the left or right line-

level input on the subwoofer, and no Y-adapter is

needed.



Speaker-Level Outputs: If you are using

the Speaker-Level Inputs



on the

subwoofer, you should connect these binding-

post terminals to your front left and right speak-

ers, remembering to maintain polarity by con-

necting the (+) terminal on the subwoofer to the

(+) terminal on the speaker, and the (–) terminal

on the subwoofer to the (–) terminal on the

speaker. If you are not using the Speaker-Level

Inputs



, then connect your front left and

right speakers directly to your receiver or

amplifier. See pages 9 through 12 for further

information on speaker connections.



Speaker-Level Inputs: Connect these

binding-post terminals to the main left and right

speaker terminals of your receiver or amplifier, if

your receiver or amplifier does not have a line-

level subwoofer output. Remember to maintain

polarity by connecting the (+) terminal on the

receiver/amplifier to the (+) terminal on the sub-

woofer, and the (–) terminal on the receiver/

amplifier to the (–) terminal on the subwoofer.



Master Power Switch: Place this switch in

the “•” position to power-on the subwoofer. The

subwoofer will then be either in the Standby

mode or completely on, depending on the

position of the Trigger On/Off Switch





AC Power Cord: Make sure to plug this

cord into an active, unswitched electrical outlet

for proper operation of the subwoofer.

The cord should not be plugged into the

accessory outlets found on some audio

components.

0127CSK - HK TS2_ENG.qxp:29515_HKTS2_English 18/03/09 16:07 Side 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HKTS 2 MkII Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info