Bedienungsanleitung Harman Kardon HKTS 20 (Seite 4 von 12) (Englisch)

534550

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

PL0004-01001

4 5

HKTS200SUB Rear-Panel Connections

Subwoofer Level Control:

.

Use this control to adjust the HKTS200SUB’s volume. Turn

clockwise to increase the volume; turn counterclockwise to decrease the volume.

Bass Boost Switch:

1.

Set this switch to ON to enhance the HKTS200SUB’s low-frequency

performance. Set this switch to OFF for normal low-frequency performance.

Phase Switch:

2.

The Phase Switch

determines whether the HKTS200SUB’s piston-like

action moves in and out in phase with the satellite speakers. If the subwoofer were

to play out of phase with the satellite speakers, the sound waves produced by the

subwoofer could be canceled out, reducing bass performance and sonic impact. This

phenomenon depends in part on the relative placement of all the speakers in the

room. In most cases the Phase Switch

should be left in the NORMAL position.

However, it does no harm to experiment, and you can leave the Phase Switch

the position that maximizes bass response and impact.

Power On Mode Switch:

3.

When set in the AUTO position and when the Power Switch

is set to ON, the HKTS200SUB will automatically turn itself on when it receives an

audio signal, and will enter the standby mode once no audio signal has been received

for about 15 minutes. When this switch is set in the ON position, the HKTS200SUB

will remain on whether or not it is receiving an audio signal.

An LED on the HKTS200SUB’s top panel indicates whether the subwoofer is in the on

or standby state:

• When the LED is illuminated white, the HKTS200SUB is turned on.

• When the LED is not illuminated, the HKTS200SUB is in standby mode.

When the Master Power Switch

7

is set to OFF, the LED will not be

illuminated, no matter what setting the Power On Mode Switch

3

is in.

External Trigger Input:

4.

Use the mini-plug of the supplied combination LFE and trigger

cable to connect the External Trigger Input to the trigger output of another

compatible component. Whenever a trigger signal between 3 and 30V (AC or DC) is

detected, the HKTS200SUB’s amplifier will turn on. The HKTS200SUB’s amplifier will

turn off after the trigger signal ceases. (This will occur even when the Power On

Mode Switch

is in the AUTO position.)

Line-Level LFE In Connector:

5.

Use the LFE (purple) connector of the supplied combination

LFE and trigger cable to connect the Line-Level LFE In to the dedicated subwoofer

output of a receiver or preamp/processor. This input bypasses the HKTS200SUB’s

internal crossover circuitry, so it should only be used with a subwoofer output that has

been low-pass filtered. If your receiver or preamp/processor does not have a dedicated

subwoofer output that is low-pass filtered you should use the HKTS200SUB’s Line-

Level L/R In Connectors

instead.

Line-Level L/R In Connectors:

6.

Use these connectors if your receiver or preamp/processor

does not have digital surround sound decoding or a subwoofer output that is low-pass

filtered.

• If your receiver or preamp/processor has a separate subwoofer output, use the LFE

(purple) connector of the supplied combination LFE and trigger cable to connect it to

either one of the HKTS200SUB’s Line-Level L/R In Connectors.

• If your receiver or preamp/processor does not have a separate subwoofer output,

use two Y-adapters (not supplied). Connect an adapter’s single end to the unit’s

preamp output for that channel. Connect one of the adapter’s dual ends to the main

amp input for that channel, and connect the adapter’s other dual end to one of the

HKTS200SUB’s Line-Level L/R In Connectors. Repeat with the other Y-adapter,

preamp channel, main amp input and HKTS200SUB Line-Level L/R In Connector.

Power Switch:

7.

Set this switch in the ON position to turn the HKTS200SUB on. The

subwoofer will then either be on or in standby mode, depending on the setting of the

Power On Mode Switch

Power Cord (Non-Detachable):

8.

After you have made and verified all subwoofer

and speaker connections described in this manual, plug this cord into an active,

unswitched electrical outlet for proper operation of the HKTS200SUB. DO NOT plug this

cord into the accessory outlets found in some audio components.

0165CSK - HK HKTS20 and HKTS30 v6.indd 4 08/10/09 13:31:51

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HKTS 20 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon HKTS 20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info