Bedienungsanleitung Harman Kardon HKTS30SAT-2 (Seite 4 von 8) (Englisch)

534549

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

4 5

NOTE: If you’re running the speaker wire through the wall you can bring it out directly

behind the bracket location and insert it through the bottom opening in the wall portion

of the wall-mount, as shown in the illustration. This will keep the wire completely hidden

from view once the installation is complete.

Insert Wire into

Bottom Opening

Bring Wire Out

through Here

If you’re not running the speaker wire through the wall, insert it through the wall 5.

portion of the wall-mount bracket as shown in the illustration.

Pass the speaker wire through the speaker portion of the wall-mount as shown in the 6.

illustration.

Bring Wire In

through Here

Bring Wire Out

through Here

If you have not already removed the speaker’s base, do so by pulling it straight off the 7.

speaker, as shown in the illustration. Applying even pressure to both sides of the base

will allow it to slide off smoothly.

Apply Pressure Evenly

to Both Sides of Base

Lift Base Straight

off Speaker

CAUTION: Before making speaker connections, be sure that your receiver or amplifier

is turned OFF and preferably, its AC cord is unplugged from the AC outlet.

Connect the speaker wire to the speaker terminals as shown in the illustration: 8.

Press down on the top of the terminal to open the connection hole.

•

Insert the wire’s bare end all the way into the hole.

•

Release the terminal to secure the wire.

•

Insert the conductor with the colored band into the speaker’s red ( + ) terminal, and

insert the other conductor into the speaker’s black ( – ) terminal.

–

Push Down on Cap to

Open Hole

Insert Bare Wire into

Open Hole

Release Cap to Secure Wire

IMPORTANT

Make sure the ( + ) and ( – ) bare wires do not touch each other or the

other terminal. Touching wires can cause a short circuit that can damage your receiver

or amplifier.

Slide the speaker portion of wall-mount onto the speaker as shown in the illustration. 9.

Fit the wall-mount bracket's grooves onto the rails in the speaker, and apply even

pressure on both sides of the mount so it slides straight onto the speaker.

Push the mount all the way onto the speaker until it snaps into place.

•

Pull any slack speaker wire back through the mount as you slide the mount onto the

•

speaker.

Fit Bracket Grooves

onto Speaker Rails

Push Down Evenly on Both Sides of Bracket

Slide the speaker onto the mount’s wall section as shown in the illustration. Pull any 10.

slack speaker wire back through the mount’s wall section.

Slide Speaker

onto Wall-Mount

Fit the metal stop plate into the recess on the bottom of the wall-mount bracket with 11.

the pad facing the bracket, and fasten it to the bracket using two of the supplied

screws. Fastening it will prevent the speaker from detaching from the wall-mount

bracket and will hold the speaker in position as you rotate it on the wall-mount

bracket.

Supplied Screws

Stop Plate

0209CSK - HK HKTS30SAT-2 Inlay.indb 4 09/04/10 8:56:05

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon HKTS30SAT-2 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon HKTS30SAT-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info