Bedienungsanleitung Harman Kardon Onyx (Seite 6 von 10) (Englisch)

534542

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Onyx

Operation

Ad-hoc Mode

If you have a Mac or PC computer, or other phone or tablet, use the following method

to connect to the system:

1. Put the Harman Kardon Onyx into Ad-hoc mode by touching

the Wi-Fi button for more than 5 seconds (ensure there

are no USB devices plugged into the USB port).

2. Go to the Wi-Fi Settings page on your Mac, PC or Phone and

connect to the network with the name HK_Onyx*****.

This may take around 40 seconds depending on your device.

3. Open your web browser and enter the IP address as

192.168.1.1 in the address bar of your browser.

The following page will be displayed.

4. Select the name of the Wi-Fi network you want to connect

from the drop-down menu Device Wireless SSID.

5. Enter the password for your network and click Connect.

A warning box will be displayed.

6. Ensure that you have entered the password correctly. If you are not sure,

click Cancel and enter the password again without any mistake.

The Harman Kardon Onyx will then attempt to connect to your Wi-Fi network. If the

connection is successful, the Wi-Fi LED will turn white and the connection successful

tone can be heard.

NOTE: To restore the factory default settings, long press Bluetooth and

Power button in Operational mode.

Operation

Switching ON and OFF

The power button on the top panel of the speaker allows you to set your speaker to any

of the following power modes:

• Operational mode – White constant LED illumination

• Sleep mode – Amber constant LED illumination

• OFF mode – No illumination

To change the power mode:

• Short press - Operational/Sleep mode: show battery status

• Long press - OFF mode: wake up to Operational mode, Operational/Sleep

mode: enter OFF mode

Adjusting Volume

The volume buttons on the top panel allow you to increase or decrease volume. These

buttons are touch-sensitive, allowing volume control with a gentle finger-touch of the

buttons. Adjust volume using the Volume Up (“+”) and Volume Down (“–”) buttons

located on top of the unit.

• Short press - Increase/decrease volume by 1 step

• Press and hold - Increase/ decrease volume continuously (1 step per 0.2

second)

Playing Music through Bluetooth

1. Press the Power button. The LED will illuminate white.

The HK Onyx enters pairing mode the first time it is switched on.

2. If HK Onyx has been paired with any source before, touch

and hold the Bluetooth button for at least 4 seconds.

3. Perform a new device search on your Bluetooth-capable device.

4. Select HK Onyx BT on the device’s pairing list and enter pasword as 0000.

The device will be paired to HK Onyx automatically. If pairing is successful,

the Onyx’s Status LED will change to white.

5. Control playback from your Bluetooth-capable device.

6. You can change the name of the speaker for easy

identification using the H/ K Remote app.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon Onyx Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon Onyx

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info