Bedienungsanleitung Harman Kardon RCP 6 (Seite 4 von 20) (Englisch)

456601

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

REMOTE CONTROL FUNCTIONS

The RCP 6 remote is capable of controlling 11 devices, including the

AVR 247 and the DVD 38 included in the CP 60 system. During the

installation process, you may program the codes for each of your source

components into the remote. Each time you wish to use the codes for

any component, first press that component’s selector. This changes the

button functions to the appropriate codes for that product.

NOTE: Several of the Input Selectors are shared between two

devices. The selector button will light in red when the remote is in

the device mode printed on the button, and it will light in green for

the device mode printed above the button. To switch between the

two device modes, press the selector

twice

quickly in succession.

The selector will remain in the last-selected mode until the next

time you press it twice quickly.

For example, the first time you press the DVD Button, the button

will light in red, indicating that the remote is in DVD mode. If you

press another selector, such as the VID3 Selector, and then press

the DVD Button again, the DVD Button will remain red, indicating

the remote is still in DVD mode. Now press the DVD Button twice

quickly. At the first press the button will light in red, indicating that

the remote is in DVD mode. On the second press the button will

turn green, indicating that the remote is now in CD mode. If you

press a different selector and return to the DVD/CD Selector, you

will observe that the remote is still in CD mode.

Each Input Selector has been preprogrammed to control certain types

of components, with only the codes specific to each brand and model

changing, depending on which product code is programmed. The

device types programmed into each selector (except HDMI 1 and 2)

may not be changed.

DVD: Controls DVD players and recorders. The DVD Button functions

are labeled in blue on the remote.

CD: Controls CD players and recorders.

Tape: Controls cassette decks.

The Bridge/DMP: Controls an iPod

docked in The Bridge.

Video 1: Controls VCRs, TiVo

and DVRs.

Video 2: Controls cable and satellite television set-top boxes.

Video 3: Controls televisions and other video displays.

Video 4: Controls a TV connected to the front-panel inputs.

HDMI 1 and 2: Each code set controls a source device (such as

a VCR/PVR, DVD player or cable/satellite set-top box) connected to

one of these two inputs.

XM: Controls the AVR functions for XM

Satellite Radio.

For example, if you have inserted a disc in your CD player and you

would like to skip ahead three tracks, but you then find that the volume

is too loud, you would follow this procedure:

1. Press the CD Input Selector to switch to the codes that control your

CD player. If the remote is in DVD mode, press the selector twice quickly

to switch to CD mode, indicated by the selector turning green.

2. Press the Play Button (in the Transport Controls section) if the disc

is not already playing.

3. Press the Skip Up Button three times to advance three tracks.

4. Press the AVR Button so that you can access the volume controls.

5. Press the Volume Down Button until the volume level is satisfactory.

Any given button may have different functions, depending on which

component is being controlled. The buttons are labeled with some of

these functions, with the receiver’s functions shown in gray, and the

DVD player’s functions shown in blue. For example, the Sleep and DSP

Surround Buttons are labeled for use as Channel Up/Down Buttons

when controlling a television or cable box. See Table A1 in the Appendix

for listings of the different functions for each type of component.

NOTE: Although we have described the applicable DVD functions

in this section, we strongly recommend that you review the

DVD 38 manual for more information about using these functions.

IR Transmitter Lens: As buttons are pressed on the remote,

infrared codes are emitted through this lens. Make sure it is pointing

toward the component being operated.

Power On Button: Press this button to turn on the AVR or another

device. The Master Power Switch on the AVR 247’s front panel must

be switched on first.

Mute Button: Press this button to mute the AVR 247’s speaker and

headphones outputs temporarily. To turn off muting, press this button

or adjust the volume. Muting is also canceled when the receiver is

turned off.

Program Indicator: This LED lights up or flashes in one of three colors

as the remote is programmed with codes.

Power Off Button: Press this button to turn off the AVR 247 or

another device.

AVR Selector: Press this button to switch the remote to the codes

that operate the receiver.

Input Selectors: Press one of these buttons to select a source

device, which is a component where a playback signal originates (e.g.,

DVD, CD, cable TV, satellite or HDTV tuner). This will also turn on the

receiver (if it is not already on) and switch the remote’s mode to operate

the source device.

AM/FM Button: Press this button to select the tuner as the source,

or to switch between the AM and FM bands.

6-/8-Channel Input Selector: Press this button to select the

6-/8-Channel Inputs as the audio source. The receiver will use the video

input and remote control codes for the last-selected video source.

XM Radio Button: Press this button to select XM Satellite Radio as

the source. You will need to have purchased and activated an XM antenna

module, and you will also need to subscribe to the XM Satellite Radio

service. Visit www.xmradio.com for more information.

RCP 6 om.qxd 3/15/07 11:19 AM Page 4

Harman Kardon RCP 6 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info