Bedienungsanleitung Harman Kardon SB 30 (Seite 4 von 16) (Englisch)

534569

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

SB 30

Input

1 2 3 4

Input

1 2 3 4

Input

1 2 3 4

Connections and Controls

Coaxial Digital Input connector: If your TV, disc player or cable/satellite tuner has a

coaxial digital output, use a coaxial digital audio cable (not supplied) to connect it here.

Optical Digital Input connector: If your TV, disc player or cable/satellite tuner has an

optical digital output, use the supplied optical digital audio cable to connect it here.

Analog Input connectors: Use the supplied stereo audio cable to connect the stereo

analog outputs of your TV, disc player or cable/satellite tuner here.

NOTE: You can connect three different source components to the three input connectors.

See

Source Connections

, on page 8 for more information.

Wireless Code switch: This switch selects among four different wireless channels for

the wireless subwoofer signal.

IMPORTANT: Be sure to set the soundbar’s Wireless Code switch to the same

channel that you set the subwoofer’s Wireless Code switch. See

Wireless Code

Switches

, on page 10, for more information.

EQ switch: This switch adjusts the soundbar’s bass performance for either wall or

table mounting. If you’re mounting the soundbar on a wall with the included wall-mount

brackets, set this switch to the “Wall” position for the most natural-sounding bass

performance. If you are placing the soundbar on a table, set the EQ switch to the “Table”

position for the most natural-sounding bass performance.

Power Cord connector: Connect the supplied AC power cord here. See

Power

Connections

on page 9, for more information.

CAUTION: Before connecting the power cord, make sure the Voltage Selector

switch (see below) is in the correct setting for your local AC voltage. See

Power

Connections

, on page 9, for more information.

Power switch: Set this switch to the “On” position to put the soundbar into the Standby

mode. In normal operation, this switch will be left in the “On” position. See

Turning the

Soundbar On and Off

on page 10, for more information.

Voltage Selector switch: This switch is set at the factory for the proper AC voltage in

the region where the soundbar is shipped. See

Voltage Selector Switch

, on page 8, for

more information.

AC Fuse holder: The SB 30 CNTR is factory-equipped with a T4AL/250V AC fuse (110 –

120V AC operation) or a T2AL/250V AC fuse (220 – 240V AC operation). If the fuse ever

blows:

1. Unplug the soundbar power cord from the AC outlet and wait for the Power LED to turn

off before proceeding.

2. Use a screwdriver to open the fuse holder.

3. Remove the blown fuse.

4. Replace the fuse with an identical fuse: T4AL/250V (110 – 120V AC operation);

T2AL/250V (220 – 240V AC operation).

CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE, REPLACE THE FUSE ONLY

WITH THE SAME TYPE AND RATING.

Connections and Controls

Soundbar Rear-Panel Controls and Connectors

Coaxial Digital

Input Connector

Optical Digital

Input Connector

Power Cord

Connector

Analog

Input

Connectors

Power

Switch

AC Fuse

Holder

Voltage

Selector

Switch

Wireless

Code

Switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon SB 30 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon SB 30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info