Bedienungsanleitung Harman Kardon SB 30 (Seite 8 von 16) (Englisch)

534569

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

SB 30

Placing the Soundbar and Subwoofer

and Connecting the System

5. After making all of the connections described in

Connecting the System

, on this page,

attach the soundbar to the brackets by sliding the slots in its feet onto the brackets’

vertical tabs.

Placing the Subwoofer

The performance of a subwoofer is directly related to its placement in the listening room

and its physical position relative to the other speakers in the system.

While it is true that in general our ears do not hear directional sounds at the low

frequencies where subwoofers operate, when installing a subwoofer within the limited

conﬁnes of a room, the reﬂections, standing waves and absorptions generated within the

room will strongly inﬂuence the performance of any subwoofer system. As a result, the

speciﬁc location of the subwoofer in the room does become important to the amount and

quality of bass that is produced.

For example, placing the subwoofer next to a wall generally will increase the amount of

bass in the room; placing it in a corner (1) generally will maximize amount of bass in the

room. However, corner placement can also increase the destructive effect of standing

waves on bass performance. This effect can vary depending on the listening position –

some listening positions may yield very good results while others may have far too much

(or too little) bass at certain frequencies.

In many rooms, placing the subwoofer along a wall away from a corner (2) can produce

the best integration between the sound of the subwoofer and that of the left and right

speakers. In some rooms, the best performance could even result from placing the

subwoofer behind the listening position (3).

SB 30 CNTR

Soundbar

We strongly recommend that you experiment with placement before choosing a ﬁnal

location for your subwoofer. One way you can determine the best location for the

subwoofer is by temporarily placing it in the listening position and playing music with

strong bass content. Move around to various locations in the room while the system is

playing (putting your ears where the subwoofer would be placed), and listen until you ﬁnd

the location where the bass performance is best. Place the subwoofer in that location.

Connecting the System

Source Connections

Analog: Use the supplied stereo audio cable to connect the soundbar’s Analog Input

connectors to your TV’s stereo audio output. If your TV has two sets of audio output

jacks, use the set that has a ﬁxed (not variable) output level. It will let you turn your

TV’s speakers all the way off while the TV still supplies a constant audio signal to the

soundbar.

Digital: If your disc player, cable tuner or satellite tuner has a coaxial or optical digital

output, you can use the supplied optical digital audio cable and a coaxial digital audio

cable (not supplied) to connect them to the soundbar’s Optical and Coaxial Digital Input

connectors. We recommend setting the component’s digital output to “Bitstream” so it

will send Dolby

Digital and DTS

bitstreams to the SB 30 CNTR for decoding. This will

produce better results when using the Virtual and HARMAN Wave surround modes (see

Surround Modes

on page 11).

NOTE: If your disc player, cable tuner or satellite tuner does not have a digital output you

can connect its analog audio output to your TV. The TV will send its audio signal to the

soundbar through the analog connection described above.

AUDIO

OUT

OPTICAL

DIGITAL

OUT

COAXIAL

DIGITAL

OUT

Input

1 2 3 4

Input

1 2 3 4

Stereo

Audio Cable

(supplied)

Optical

Digital Audio Cable

(supplied)

Coaxial

Digital Audio Cable

(not supplied)

Satellite Tuner

Disc Player

SB 30 CNTR Soundbar

Voltage Selector Switch

The soundbar’s Voltage Selector switch is set at the factory to accommodate the AC

power voltage in the area where the soundbar is shipped.

IMPORTANT: Before you connect the power cord for the ﬁrst time it is a good idea

to verify that the setting of the voltage selector is appropriate for the power in

your area.

In the event that you do need to change the Voltage Selector switch setting:

1. Make sure that the soundbar is powered off and the power cord is disconnected from

the soundbar.

2. Slide the Voltage Selector switch to the appropriate setting (“110 – 120V” or “220 –

240V”) as required for your area.

WARNING: DO NOT UNDER ANY CIRCUMSTANCES OPERATE THE SOUNDBAR WITH

THE WRONG VOLTAGE SELECTED. DOING SO MAY RESULT IN SERIOUS DAMAGE TO

THE SOUNDBAR, WHICH WILL NOT BE COVERED BY WARRANTY.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon SB 30 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon SB 30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info