Bedienungsanleitung Harman P43-C (Seite 20 von 40) (Englisch)

815496

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Harman® • P-Series Owner’s Manual_R16 • 2018 - ___ • 01/2320 8390-044C

STOVE DOES NOT FEED

1. No fuel in hopper.

2. Fireboxdraftmaybetoolowforsensingswitchinfeeder

circuit to operate. Check for closed doors, loose or

missing gasket on doors or hopper lid.

3. Feed motor will not run until the ESP control senses a

certain temperature. Maybe you did not put enough fuel

or starting gel in the burn pot before manually lighting the

re.

4. Restriction in the hopper or feeder. Remove all fuel and

examine.Cleartheobstruction.

5. Feed motor has failed.

PARTIALLY BURNED PELLETS

1. Feed rate too high.

2. Poorairtofuelmixture.(Checkburnpotclean-outcover

andairintake).

3. Burnpotorheatexchangertubesmayneedtobecleaned.

4. Combination of all the above.

5. #6 status blink: A 6 blink control board status indication

is caused by poor or incomplete combustion. The circuit

board has the ability to track the combustion through feed

settings and ESP temperatures. When the control board

has calculated poor or incomplete combustion, it will shut

downtheunit as a safety feature. (Poor or incomplete

combustion is a contributor of creosote which may cause

achimneyre)

A 6 blink status may be caused by several things:

1. Blockedorpartiallyblockedue.

2. Blocked or partially blocked inlet air.

a. Backdraft damper on the inlet pipe may be stuck closed.

b. If outside air is installed, the inlet cover may be blocked.

3. Theairchamberundertheburnpotmaybelledwithnes

and small bits of ash.

4. Theholesintheburnpotmaybegettinglledwithashor

carbon buildup.

5. Combustion blower fan blades may need cleaned.

6. Fuel restrictions as noted above.

SMOKE SMELL

Follow venting manufacturer’s recommendations for sealing

pipejoints.Theexhaustventistheonlypartofthesystem

that is under positive pressure.

FIRE HAS GONE OUT- Check for status light.

1. No fuel in hopper.

2. Draftistoolow,blockedue.

3. Somethingisrestrictingfuelow.

4. Hopper lid not closed properly.

5. Feed motor or combustion blower has failed.

SMOKE IS VISIBLE COMING OUT OF VENT

1. Air-fuelratioistoorich.

a. Feed rate too high.

b. Draft too low caused by a gasket leak.

LOW HEAT OUTPUT

1. Feed rate too low

2. Draft too low because of gasket leak.

3. Poor quality or damp pellets

4. Combination of 1 and 2.

HELPFUL HINTS

1. Cleaning Burn Pot

Whenever your stove is not burning, take the opportunity to

scrape the burn pot to remove carbon buildup. A vacuum

cleaner is handy to remove the residue. Be sure the stove

is cold if you use a vacuum.

Carbonbuildupcanbescrapedloosewiththereburning

using the special tool provided with your stove. Scrape the

oorandsidesoftheburnpot.Thecarbonwillbepushedout

by the incoming fuel. Always wear gloves to do this.

2. Removing Ashes

TurntheTempDialtonumber1approximately30minutes

before removing ashes. This will result in a cooler stove and

ash pan.

Maximum Feed Limit settings are not needed in most

cases.Operatinginthenormalrange(#4)isrecommended

whenmaximumheatoutputisnotrequired.TheESPprobe

preventsthestovefrombeingover-red.

Keep the stove free of dust and dirt.

Fuel

TheP-SeriesPelletStoveisapprovedforburninganygrade

ofpelletizedbio-massfuel.

It should be noted, however, that higher ash content will

require more frequent ash removal, scraping of the burn pot,

and may provide less BTU’s per pound.

Themoisturecontentofpelletsmustnotexceed8%.Higher

moisture will rob BTU’s and may not burn properly.

Fuel should not be stored within the stove installation

clearances or within the space required for cleaning and

ash removal.

C. Troubleshooting

Withproperinstallation, operation, and maintenance your appliance will provide yearsoftrouble-freeservice.Ifyoudo

experienceaproblem,thistroubleshootingguidewillassistaqualiedservicepersoninthediagnosisofaproblemandthe

correctiveactiontobetaken.Thistroubleshootingguidecanonlybeusedbyaqualiedservicetechnician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman P43-C Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman P43-C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info