815498
16
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
Harman® • P-Series Owner’s Manual_R16 • 2018 - ___ • 01/2316 8390-044C
Whenever adding fuel, take the opportunity to clean the burn
pot. (Weekly at minimum)
Scrape the top holed surface and sides of the burn pot
down to auger tube Figure 5.1. It is not necessary to
completely remove all material from the burn pot. The
excesswillbepushedoutduringthenextuse.
• With the re out and burn pot cold, use the supplied
allen wrench to remove any build-up that may have
accumulated in the holes of the burn pot grate. Simply
push the allen wrench down through each hole ensuring
itisclearofanybuild-uppayingattentionnottodamage
the igniter element in the process.
Monthly, or after each ton of fuel burned:
• Loosenthe(2)wingthumbscrewsonthelowerfrontangle
of the burn pot. Figure 5.2
• Lifto󰀨theclean-outcovertoopenthebottomclean-out
chamber. Figure 5.3
Clean ash buildup from inside the chamber while cover
iso󰀨.Usethescrapertotaponthetopfrontedgeofthe
burn pot. This will help knock pieces of ash, loosened
by the scraping process, down through the holes. It also
helpsknockscaleo󰀨oftheigniterelement.
Figure 5.3
The igniter is made to be removable for service by insulated
male/female wire connectors. These connections between
thehotleads(thewiresinsidetheburnpot)andthecold
leads(thewiresfromthecontrolboard)arealwayspulled
to the inside rear of the feeder body. (Not coiled inside the
burn pot.)
It is very important that these connections are to the inside
rearofthefeederbody.Also,theextrawireoftheigniterwire
service loop must be pulled out through the rear of the feeder
and tied up so that it will not be damaged by any moving parts.
Note: The hot lead/cold lead connection must always be
pulled to the rear of the feeder body before operation.
E. Burnpot Maintenance
Figure 5.1
Figure 5.2
Wing Thumb Screws
Figure 5.3 - View from below through the ash pan opening.
Igniter hot lead wires
(High temperature)
Burn pot igniter
Use caution when cleaning burn pot clean-out
chamber. Do not damage the high temperature igniter
wires.
WARNING
Disconnect the power to the unit before removing
cover.
DANGER
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Harman P68-C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Harman P68-C

Harman P68-C Bedienungsanleitung - Französisch - 40 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info