Bedienungsanleitung Hartke HA5500 (Seite 11 von 72) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

624014

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Guided Tour - 3500/5500 Rear Panel

6. Effect Return jack - Use this 1/4” unbalanced jack to return low impedance

(600 ohm) signal to the Model 3500/5500 from a professional outboard effects

processor.*

7. Balance control - Use this to adjust the relative amount of Effect Send (dry)

versus Effect Return (wet) signal being routed to the Model 3500/5500 speaker

outputs. At the center-detented “0” position, equal amounts of Send and Return

signal are routed. At its fully counterclockwise (“Send”) position, no signal from a

connected effects processor(s) is added to the main output. At its fully clockwise

(“Return”) position, the only signal you hear is that coming from a connected out-

board effects processor(s). If your outboard effects processor has an adjustable

wet/dry control, we recommend that you set the Balance knob to its fully clock-

wise (“Return”) position and use the effects processor’s wet/dry control to adjust

the relative mix. Alternatively, you can set the effects processor to output fully

“wet” signal and use the Model 3500/5500 Balance knob to adjust the relative

mix of dry vs. wet signal

8. Direct Out Post/Pre switch - When pressed in (the “Pre” position), signal is

routed to the Direct Out jack prior to the Model 3500/5500 ten-band graphic

equalizer (but after the compression circuitry and Contour controls). When out

(the “Post” position), signal is routed to the Direct Out jack after all compression

and EQ circuitry (both ten-band graphic and Contour).** Use the “Pre” position

when you want the console engineer to have control over equalizing your bass

signal; use the “Post” position when you want to use the front panel ten-band

graphic equalizer to equalize your bass signal before sending it to the console.

9. Direct Out Normal/Ground Lift switch - When pressed in (the “Gnd. Lift” posi-

tion), pin 1 is removed from the chassis. This should be used only when a ground

loop hum or buzz is heard; otherwise, leave it in the out (“Normal”) position.

10. Direct Out jack - Use this electronically balanced XLR jack to route signal

from the Model 3500/5500 to a professional mixing console or as a tap to a main

PA system via a mic input on the console. The signal output from this jack is low

impedance (100 ohm) with an output level of approximately -30 to -20 dB. You

can also use the Direct Out jack to route signal to an external amplifier with a -10

dB input sensitivity.

* In-line effects (such as footpedals) intended for low signal levels should be placed

between the bass and the amplifier Input and not connected with the Effect Send and

Return jacks.

** Note that the settings of the ten-band graphic equalizer will affect a “Post” Direct

Out signal regardless of the position of the front panel In/Out switch.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hartke HA5500 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info