Bedienungsanleitung Hayward AquaRite Pro Touch Salt Chlorinator (Seite 33 von 136) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

801942

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Only use spare parts supplied by Hayward brands®

Page 15 on 16AquaRite® Pro Touch

6. SERVICING

During the rst 10-15 days, your system will require more attention:

- Check that the pH remains at the ideal level (7.2 to 7.4).

- If the pH is exceptionally unstable and uses a lot of acid, check the alkalinity (see table).

If the balance is highly unstable, contact your pool installer/builder.

REMEMBER that the system needs a certain amount of time to adapt to your pool and will require additional chemicals

during the rst 3-5 days.

The pool must be regularly maintained and the skimmer baskets emptied whenever necessary.

Also check that your lter is not clogged.

ADD WATER: It is preferable to add water via the skimmers so that it passes through the cell before entering the pool.

Remember to check the salt percentage after adding water.

DOSING PUMPS: Regularly check the acid level to ensure that the pump does not run dry. The dosing pump must be checked

and serviced at regular intervals. The Santoprene tube of the peristaltic pump has a lifetime of 2 years. We recommend that

you change it once a year.

Servicing the probe

The probe must be clean and free from oil, chemical deposits and contamination to function properly. As it is in continuous

contact with the water in the pool, the probe may need to be cleaned weekly or monthly, depending on the number of bathers

and other specic pool characteristics. A slow response, more frequent pH calibration and inconsistent readings indicate that

the probe needs to be cleaned.

To clean the probe, turn off the power to the AquaRite® Pro Touch.

Unplug the probe connector from the control box, unscrew the probe and carefully remove it from the chamber. Clean the

probe bulb with a soft toothbrush and regular toothpaste.

A household washing-up liquid detergent may also be used to remove any oil.

Rinse with fresh water, replace the Teon tape on the threads, and reinstall the probe.

If the probe continues to give inconsistent readings or requires excessive calibration after it has been cleaned, it should be

replaced.The lifetime of the probes is 1 year. We recommend that you calibrate them every month during the season the

pool is in use.

Servicing and cleaning the AquaRite® Pro Touch cell

Turn off the main power supply to the AquaRite® Pro Touch before removing the cell. Once it has been removed, examine the

inside of the cell for any traces of scale (whitish brittle or aky deposits) and debris stuck to the plates. If no deposits are visible,

reinstall the cell. If deposits are visible, try to remove them with a garden hose. If this method is unsuccessful, use a plastic or

wooden tool to remove deposits stuck to plates (do not use a metal tool as this will damage their coating). A build-up of deposits

on the cell indicates an exceptionally high concentration of calcium in the pool water. If you cannot nd a solution to this situation,

you will have to clean the cell at regular intervals. The best way to avoid this problem is to maintain the chemical composition of

the water at the recommended concentrations.

Acid washing: This should only be done in severe cases where ushing will not remove most of the deposits. To acid wash, turn

off the main power supply to the AquaRite® Pro Touch. Remove the cell from the piping. In a clean plastic container, make up

a solution of water and acetic or phosphoric acid (such as that used to remove scale from a coffee machine). ALWAYS ADD

ACID TO WATER – NEVER ADD WATER TO ACID. Be sure to wear rubber gloves and protective goggles for this operation.

The level of the solution in the container should just reach the top of the cell, so that the wire harness compartment IS NOT

under water. It may be helpful to coil up the wire before submerging the cell. Allow the cell to soak for a few minutes, then rinse

it with a garden hose. If the deposits are still visible, soak and rinse again. Put the cell back and examine it from time to time.

The lifetime of the cell is 3 years under ideal conditions. See the chapter on chemical water balance.

Wintering

The AquaRite® Pro Touch cell, the ow switch, probe and pool piping run the risk of being damaged if the water freezes. In

regions that experience long periods of cold weather, be sure to drain all the water from the pump and lter and from the

supply and return pipes before winter. Do not remove the control box.

Probe storage

The end of the probe must always be in contact with water or a solution of KCl. If it is removed from the measuring chamber,

it should be stored in the plastic cap provided (lled with water). If the storage cap has been mislaid, the probe should be

stored separately in a small glass or plastic container with its end immersed in water.

The probe must always be in a frost-free environment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hayward AquaRite Pro Touch Salt Chlorinator Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info