Bedienungsanleitung Hayward Max-Flo Pump (Seite 12 von 65) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

801928

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Page 5 of 6 Pump Rev. B

Electrical connection: Make sure that the power supply voltage required by the motor corresponds to that of the distribution

network and that the power supply cables matches the power and current of the pump.

All the electric connections of the pump and the possible change of power supply cable must be hand-led by a qualified

professional so as to avoid all possible danger.

When making these electrical connections, refer to the diagram given under the lid of the motor terminal box.

Be sure to check the electric connections are tight and sealed before powering up.

The pre-wiring that might be included on some of the pumps must be removed for final connection of the pump to the electric

power supply. This pre-equipment is only used for works testing during the manufacturing phases.

INSTALLATION

Install the pool pump so as to reduce pressure drops to a minimum whilst complying with the distances specified in the

installation standard, namely 3.5m minimum between the pump and the pool. The suction pipe must be installed with a

slight uphill incline towards the pump axis. Ensure that the connections are correctly tightened and watertight. However,

avoid excessively tightening the pipes. For plastic materials, use Teflon only to ensure watertightness. The diameter of the

suction pipe shall depend on that of the discharge pipe. Avoid damp or non-ventilated locations. The motor requires the

cooling air to circulate freely.

IMPORTANT: Check the direction of rotation before permanently connecting the motor.

INSTRUCTIONS FOR START-UP AND PRIMING: Fill the body of the strainer with water up to the level of the suction pipe.

Never run the pump without water, as the water is necessary for cooling and lubrication of the mechanical shutter. Open

all the suction and discharge pipe valves, and the filter air purge valve if there is one. (Any air in the suction pipes must be

eliminated). Start up the generator and wait a reasonable time for priming. Five minutes is not excessive for priming (this

time depends on the suction head and the length of the suction pipe). If the pump does not start or does not prime, please

refer to the troubleshooting guide.

MAINTENANCE

1. Completely disconnect the pump from the mains power supply before opening the cover and cleaning the strainer. Clean

the strainer basket regularly. Do not bang on the basket to clean it. Check the seal on the cover of the strainer and

replace it if necessary.

2. The motor shaft is mounted on self-lubricating bearings which do not require any subsequent lubrication.

3. Keep the motor clean and dry and ensure the ventilation openings are not blocked.

4. The seal assembly occasionally starts to leak and must then be changed. You can replace it preventively every two

years.

5. Apart from cleaning the pool, all repairs, servicing and maintenance must be carried out by a Hayward-approved agent

or a qualified person.

WINTERING

1. Empty the pump by removing all the drain plugs and store them in the strainer basket.

2. Disconnect the pump, remove the pipe connectors and store the entire unit in a dry, well-ventilated place or at least take

the following precaution: disconnect the pump, remove the 4 bolts attaching the pump housing to the motor bracket and

store the unit in a dry, well-ventilated place. Then cover the pump housing and strainer to protect them.

N.B.: Before recommissioning the pump, clean all the internal parts to remove dust, lime scale etc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hayward Max-Flo Pump Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info