Bedienungsanleitung Hayward PoolVac Ultra (Seite 4 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

801940

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

CONGRATULATIONS !

You have just become the owner of the latest and

most sophisticated automatic pool cleaners.

The cleaner is powered by your pool’s filtration sys-

tem and is designed to operate with most existing

systems. Its performance will therefore depend on

how powerful your pump is.

INSTALLING THE CLEANER

Step 1. Clean or back-wash your filter and clean

your pre-filter basket before installing the cleaner.

Clean your system regularly as the characteristics

of your installation dictate.

Step 2. Check the chemical properties of your

water. Make sure that the chemical balance is cor-

rect and that the pool is free of algae. Check the

pool and remove anything that might plug the suc-

tion port of your cleaner, in particular large clumps

of leaves.

Step 3. There are nine (9) 1,2 m connecting hoses

and a 1,2 m main hose with a grey end. Connect

the hose sections together. Insert the male end

of one hose firmly into the female end of another

hose and turn (see. figure 1). Depending on the

shape and size of your pool, you may not need all

the hoses. But you must always connect the main

hose, or the cleaner will not work properly. The

hose lengths need not be forced home. but must be

tight enough to prevent air leaks. Wetting the ends

of the hoses will make it easier to join them.

Step 4. From the skimmer. the complete hose

should reach the farthest part of the pool, with two

sections to spare for depth. This extra length is

essential to the proper operation of the cleaner.

If your complete hose is not long enough, you will

have to buy extra lengths from your dealer. After

connecting the correct length of hose. insert the leaf

trap and the AEV096 vacuum gauge between the

length of hose connected to the skimmer and the

next length. The vacuum gauge is used to measure

the water flow when the cleaner is started up (see

figure 2).

Step 5. Check that the rear flap adjustment knob is

in fact set to II, the intermediate position (see figure

3). Immerse the cleaner in the water to drive out all

trapped air. When al air has been eliminated, the

main hose can be connected. The main hose has

a grey end and a red sticker that must be removed.

Connect the grey end to the cleaner (as shown in

figure 4) and immerse the hose to drive out the air

as for a manual cleaning.

Do not use the return line/inlet water to «sink» the

hose, as this will force air into the cleaner head, and

possibly cause performance problems.

Step 6. With the filtration system off, connect the

hose to the skimmer as shown in figures 5, 6. and

7. Figure 5 shows the connection of the hose to

a skimmer with a bottom suction port, using the

AEXV093BP adapter cone. Figure 6 shows the

connection to a port on the side or back, for which

the AEXV151 adapter cone, available from your

dealer, must be used. The hose may be connected

through either the slit or the cover of the skim-

mer. Figure 7 shows the connection of the hose

to a skimmer with a direct suction port in the pool.

The AEXV093BP adapter cone is connected to

the connector supplied with your skimmer for the

manual cleaner. The prefilter cover supplied with

the skimmer must also be used for the cleaner to

work property. If the cover does not close tight, get

in touch with your dealer to see if another acces-

sory is needed.

Step 7. Start up the filtration system. Check the

level on the AEV096 vacuum gauge (see figure

2 for its installation). It measures the water flow

created by your pool’s filtration system and should

indicate a vacuum of at least 100 mm (4’’). The

vacuum should be about 25 mm (1’’) per length of

hose used. For example, if you use ten (10) lengths

of hose, you will adjust the water flow in the cleaner

so that the vacuum gauge indicates a vacuum of

250 mm (10’’), with a tolerance of plus or minus 25

mm (1’’). This is a rough value, and a slightly higher

or lower reading is perfectly acceptable.

Coiling the hose may impair

the operation of the cleaner.

The warranty does not cover

problems caused by coiled

hoses. Always stow the

lengths straight.

Remark: The cleaner should

not be used for the pool’s first Spring-cleaning;

unless the conditions stated in steps 1 and 2

we met. Whenever your pool is clogged with

an unusually large amount of debris, take the

necessary steps to restore its ‘pre-installation’

appearance.

Always carry the cleaner by its handle. Never

by the hose.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hayward PoolVac Ultra Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info