Bedienungsanleitung Hayward SuperPump VSTD (Seite 19 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

801903

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

USE ONLY HAYWARD® GENUINE REPLACEMENT PARTS

18 Pump

Electrical connection: Ensure that the supply voltage required by the motor corresponds to that of the distribution network

and that the section and length of the power cable are adapted to the power and current of the pump.

All the electrical connections on the pump and any change of power cable must be done by a qualified professional to avoid

any danger.

When carrying out the electrical connections, comply with the identification under the connection terminals.

Check that the electrical connections are correctly tightened and watertight before switching on the power.

Ensure the cable runs correctly through the opening and ferrite provided for this purpose. The cable gland ensures

watertightness around the cable, and the ferrite acts as a filter against electromagnetic disturbance.

Any pre-wiring on our pumps must be removed when the pump is permanently connected to the power supply. This

preparation is only used for testing at the factory during the manufacturing phases.

INSTALLATION

Install the pool pump so as to reduce pressure drops to a minimum whilst complying with the distances specified in the

installation standard, namely 3.5m minimum between the pump and the pool. The suction pipe must be installed with a slight

uphill incline towards the pump axis. Ensure that the connections are correctly tightened and watertight. However, avoid

excessively tightening the pipes. For plastic materials, use Teflon only to ensure watertightness. The diameter of the suction

pipe shall depend on that of the discharge pipe. Avoid damp or non-ventilated locations. The motor requires the cooling air

to circulate freely. Install the pump under shelter to avoid the control unit being subject to heavy splashing.

INSTRUCTIONS FOR START-UP AND PRIMING: Fill the body of the strainer with water up to the level of the suction pipe.

Never run the pump without water, as the water is necessary for cooling and lubrication of the mechanical shutter. Open

all the suction and discharge pipe valves, and the filter air purge valve if there is one. (Any air in the suction pipes must be

eliminated). Start up the generator and wait a reasonable time for priming. Five minutes is not excessive for priming (this

time depends on the suction head and the length of the suction pipe). If the pump does not start or does not prime, please

refer to the troubleshooting guide.

USING THE CONTROL PANEL

1. INTRODUCTION

Hayward®'s variable speed pump is operated through a control panel that visually displays the operating settings and

allows you to adjust them as well as program the Timer mode.

1Power on LED

2LCD display screen

3Choosing the speed

4Switching between Manual/Timer modes

5Up/down buttons

6Start/Stop button

7Display settings button

8Selected speed LEDs

The pump is delivered with DEFAULT SETTINGS(factory settings):

Priming time

(seconds) Priming

speed (rpm) V1

(rpm) V2

(rpm) V3

(rpm)

Skimmer

time

(minutes)

Skimmer

cycle (hours) Skimmer

speed (rpm)

240 3000 1500 2400 3000 15 1hr 2800

rpm: Rotations per minute

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hayward SuperPump VSTD Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info