Bedienungsanleitung Heco AMBIENT 5.1 A (Seite 9 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

535966

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

• Do not use any cleaning agents or chemical solvents when cleaning, as these could damage the

surface of the device.

• Repairsmustalwaysbeconductedbyqualifiedspecialists,asyoumightotherwisebeexposedto

dangerous high voltage levels or other hazards.

GENERAL NOTES ON CONNECTING YOUR HECO SATELLITE SPEAKERS

The connectors are located at the rear of the satellite speakers. They are equipped with a clamping

mechanism for cables cross-sections of up to 1 mm². To connect the satellites, please use normally

available 2 x 0.75 mm² – 2 x 1 mm² loudspeaker cables. The cables are to be cut to the required length,

the ends stripped and the end of the wires twisted to make it easier to connect them to the terminals.

Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables. For

good sound the cables must be connected so that the speakers are “in phase”. This means that the black

negative terminals on the speakers (-) must be connected to the negative (-) terminals on the amplifier,

the positive (+) speaker terminals to the positive (+) amplifier terminals.

Before switching on the system double-check all your connections and make sure that the terminal

screws are tight and that there are no short circuits caused by stray wire filaments – this could cause

serious damage to your amplifier!

Fig. 1 shows the use of the supplied wall mounts for the satellites.

Important information/safety instructions:The customer is solely responsible for the use of wall brack-

ets / speakers attachments. The customer is also solely responsible for the secure attachment of the

speaker bracket to the wall and the selection of suitable mounting material (e.g. screws, wall plugs, etc.),

while taking account of the weight and construction of the speaker and the condition of the wall.

POSITIONING

The centre, front and rear loudspeakers are marked on the back. The satellite connected to the centre

output should be positioned on top of or beneath your TV set. The front satellites are placed to the left

and the right of the TV set, preferably at equal distance and at ear-height. The satellites connected to

the rear/surround outputs should be located to the left and right behind the listening position and slightly

above ear-height.

Placement of the subwoofer is generally not critical. It should, if possible, be located near the front

satellites.

CONNECTION TO AN AV RECEIVER

Connection of the system to an AV receiver is shown in figure 2 (receiver without a subwoofer output),

figure 3 (receiver with low-level subwoofer output).

Note: In the receiver set-up, the front, centre, and rear loudspeaker channels should be set to ‘small’.

Some receivers also provide the option of setting the cross-over frequency between the subwoofer and

satellites. If this is the case, please set this frequency to 150 Hz or the frequency that comes closest to

150 Hz. Please consult the user manual supplied with your receiver.

THE ACTIVE SUBWOOFER

Figure 4 shows the subwoofer’s controls:

GBGB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Heco AMBIENT 5.1 A Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info