Bedienungsanleitung Hendi KC 96 V (Seite 9 von 26) (Englisch)

741192

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

_ Electric Cookers _ rev. 1 ______________________ KCP96 V – KCP96 VS – KCP5 96 V – KCP5 96 VS – KC 96 V –

KC 96 VS – KC 96 M – KC 96 MS – KCR 96 V _

_ CATEGORY II2H3+ _ GB __

0705

_____________________________________________________ page 9 _

Residual risks

- Keep away from the appliance unskilled personel.

- With hot oven, open the door carefully in order to avoid violent hot fumes exit, that my

cause burning.

- The appliance contains electrical parts and must never be washed with a jet of water or

steam.

- To avoid wrong installation, the right gas connection is showed on a label that identifies the

correct gas type to use.

- The appliance is electrically connected: before attempting any cleaning operation, cut power

to the appliance.

- Do not use the door handle to move the appliance (the glass panel may break).

- The removable parts of the cooking top, after the cleaning operation, must be placed

correctly in their housing in order to avoid anomalous and dangerous functioning of the

burners.

4. Gas connection

Connect the appliance to a gas cylinder or mains gas pipe according to the prescriptions of

standards (as per current national installation norms and subsequent amendments). To connect

gas, use an approved rigid metal pipe in copper or stainless-steel (the current national

installation norms and subsequent amendments). The appliance is equipped with threaded GJ

½” pipes for gas inflow. Check if the appliance is designed to operate on the same type of gas

as supplied and if pressure is set for that type of gas. Otherwise, carry out the operations

indicated in paragraph “ADAPTING TO DIFFERENT TYPES OF GAS”.

IMPORTANT -

Make sure that supply pressure matches the values indicated in the table

“Burner and nozzle characteristics” (tab.1-2).

If supply pressures do not match the values in the table, eliminate the cause of this, or inform

the gas company and do not use the appliance. Connection with rigid or flexible metal pipes

must not cause stresses to the appliance pipe (“train”).

5. Electric connection

Before performing the electric connection, make sure that:

- the relief valve and the system can stand the appliance load (see data on the rating

plate);

- THE SUPPLY SYSTEM IS EQUIPPED WITH AN APPROPRIATE GROUND CONNECTION IN

ACCORDANCE WITH THE REGULATIONS IN FORCE;

- the omnipolar system used for the connection can be easily reached with the appliance

installed.

In the grid-connected mode, between the appliance and the grid an omnipolar switch must

be inserted, having a 3 mm minimum opening between contacts, suitable to the load used

and in accordance with the regulations in force. The yellow/green earth cable must not be

interrupted by the switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi KC 96 V Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hendi KC 96 V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info