Bedienungsanleitung Hendi 226094 (Seite 7 von 40) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

741203

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

INSTALLATION

GENERAL INSTRUCTION

The appliance described in this manual has been built to meet 2014/35/EU (Safety), 2014/30/EU (EMC), Re 2016/426/EU

(GAR), Re 1935/2004/EC, Re 2023/2006/EC directives; and UNI EN 203…, UNI EN 437, EN 60335-1, EN60335-2-36 and

EN55014 standards. This appliance has been designed exclusively for cooking food, any other use is considered improper: be

careful that no live animal, person or “dangerous” objects are placed inside the oven. It should only be used by qualified

personnel in professional kitchens. Materials in contact with foodstuffs are suitable for use. The unit must never be left

unattended when it is being used! The appliance should be checked once a year by a qualified technician. Switch the appliance

off in the case of a failure or malfunction.

The appliance should be installed under an extractor hood for removing any cooking fumes.

Care must be taken when using the appliance because the cooking surfaces are very hot. The appliance must be

installed, connected and serviced properly by qualified personnel according to the regulations and directives in force in

the country where it is installed, as well as the instructions in this manual.

UNIT CHARACTERISTICS

These installation and user's instructions refer to the category II2H3+ gas ranges. The data plate is outside the back panel to

the appliance. The supplementary plate is also made of self-adhesive polyester and is affixed near the data plate; it contains all

information regarding the appliance. The gas distribution network fitting fig.1 meets ISO 7/1 and ISO 228/1 standards with a ø

½” connection, situated at the back of the machine. The structure of the appliance is made of stainless steel, the burners are

made of cast iron and the oven is made of stainless steel. All models have adjustable feet. The main gas pipe is made of

galvanized steel. The pipes between the tap and burner are made of copper.

Install a shut-off cock in the line between the appliance and the gas distribution network. Install an omnipolar switch

between the appliance and the electrical distribution network.

CONNECTION TO THE GAS DISTRIBUTION NETWORK

Before you install the appliance, make sure that the gas company has authorised the installation, compare the

data relevant of the appliance (data plate) with the local supply.

Remove the packaging from the appliance as well as the protective plastic sheet, and, if necessary, remove traces of glue with

a suitable solvent. To dispose of the packaging, follow local directives (for more details refer to the chapter “ECOLOGY AND

THE ENVIRONMENT”. Prior to connecting the unit to the gas network, check the data plate to see if the unit has been set and

tested for the type of gas supplied. If the gas type indicated on the data plate is not the same as that supplied, please refer to

the paragraph “CONVERSION AND ADAPTATION”. Connect the appliance to the gas distribution network using metal pipes

with a suitable diameter; install a homologated shut-off cock between the appliance and the distribution network. If flexible pipes

are used, they must be made of stainless steel according to the standards in force. When installing the appliance, all the

regulations in force must be observed, such as:

 Installation and safety standards in force.

 Regional and/or local regulations, such as building codes.

 Directives and regulations of the electricity board.

 Accident prevention regulations in force.

 Fire prevention regulations.

Applicable I.E.C. regulations.

We recommend installing the appliance in a well-ventilated environment, or under an extraction hood to remove the fumes or

vapors produced during the cooking cycle. All models have an equipotential earth terminal fig.1 in the bottom. The appliances

with an electric oven have a hole for the cable fig.1. The appliance can be installed alone or in line. Respect a minimum

distance of 80mm between the appliance and any walls made of flammable material, partitions, kitchen furniture or nearby

equipment. The contact surfaces must be covered with non-combustible heat insulating material. The appliance, and especially

the power lead, must not be installed anywhere near heat sources and the temperature of the place in which the appliance is

installed must not rise above 50°C. After installing the appliance check for any leaks in the fittings. Use non-corrosive foam

products, such as leak detection sprays, to look for any leaks.

When checking for leaks do not use naked flames!

The manufacturer shall not be held responsible and the guarantee is void in the case of damage caused by negligence

in following the operating and installation instructions or by improper use. The guarantee is void in the case of

connections which have been made in a way which doesn't meet the current standards and fire-fighting regulations.

EVACUATION OF BURNT GASES: A1 APPLIANCE

Appliances must be installed under an extraction hood with forced draught, subjected to gas supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 226094 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info