Bedienungsanleitung Hendi 226094 (Seite 11 von 40) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

741203

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

TURNING THE GAS OVEN ON AND OFF

All the cooking must be done with the oven door closed.

The burner has a safety valve that cuts off the gas supply if the flame should accidentally go out.

TURNING THE OVEN ON:

Open the oven door.

Set the knob to the desired temperature 125-250°C.

At the same time press piezoelectric igniter several times, to light the pilot flame.

After the flame has lit, hold the knob down for roughly 10 seconds; so the thermocouple heats up and

keeps the safety valve open.

Through the hole in inspection cover fig.7 check that the flame is alight.

TURNING THE GAS OVEN OFF:

Turn the knob to position “0” pressing it slightly so it goes past the stop at the minimum position.

WHAT TO DO IF THE UNIT IS NOT GOING TO BE USED FOR A LONG TIME

Turn the gas shut-off cock installed upstream of the appliance off. Clean the unit thoroughly following the instructions and dry it

carefully.

MALFUNCTIONS

In any case, if you suspect the presence of anomalies, ALWAYS CLOSE the gas shut-off cock and inform the authorized after-

sales service.

Unauthorized persons should never attempt to repair the appliance, or carry out maintenance. Tampering with the

appliance voids the warranty!

OPERATIONAL CHECKS

Before the unit is delivered to the user the following checks must be carried out:

THERMAL CAPACITY: Check that the pressure and type of gas supplied where the unit is to be used is the same as that

indicated on the plate. If it is not, the unit must either be converted or adapted. In this case please refer to the paragraph:

“Conversion or Adaptation”. Check that the right nozzles have been installed. Refer to the nozzle table and check that the

nozzles indicated in the table are the same as those installed on the unit. An additional check of thermal capacity entails

verifying the gas consumed with the volumetric method: light the burner and after approximately 10 minutes (operating

conditions) check that the gas flow (in m

/h or in kg/h) corresponds to that indicated in nozzle table.

APPEARANCE OF THE FLAME AND PRIMARY AIRFLOW: The flame should be blue and there should be no yellow dots in it;

it must be stable at its base. If the colour of the flame tends towards yellow, it means the primary airflow is not adjusted properly.

If the primary airflow is too fast the flame will be short and tend to burn above the burner. The appearance of the flame must

also be checked 15 minutes after the appliance has been running at full power. The flame must remain stable even when

passing quickly from minimum to maximum.

USER'S INSTRUCTIONS: The user must be trained on the correct use and functions of the appliance. We would like to point

out that any alterations made to the room where the unit is installed could influence the amount of air used for combustion and

for this reason the function of the unit must be checked again. When these checks have been done, test the unit for leaks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 226094 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info