Bedienungsanleitung Hendi KC 96 MS (Seite 10 von 26) (Englisch)

741195

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

_ TECNOEKA Srl _________________________________________________________ use and instruction manual _

_ page 10 ________________________________________________________________________________________

Connection of power cable

Mod. KCP96 V - KCP96 VS – KCR 96 V - The terminal board is on the rear panel of the

appliance. Open the terminal board cover by obtaining leverage with a screwdriver on the two

side fins. Loosen the cable gripper screw and allow the cable to pass through it. Arrange the

conductors so that the earth conductor is the last to detach from its terminal if the cable goes

into a state of faulty traction.

Connect the phase conductor to the terminal marked with the letter "L", the neutral

conductor to the terminal marked with the letter "N" and the earth conductor to the terminal

marked with the symbol . Tighten the ring-nut of the cable gripper and close the terminal

board cover. The appliance must be connected to an equipotential system whose efficiency

must first be checked according to current legal regulations. This connection must be made

between different appliances by using the appropriate terminal marked with the symbol . The

equipotential conductor must have a minimum diameter of 10 mm

The equipotential terminal

is at the rear of the appliance. When the appliance is operating, the supplied voltage must not

deviate from the nominal voltage value of ±10%.

Mod. KCP5 96 V – KCP5 96 VS – KC 96 V – KC 96 VS – KC 96 M – KC 96 MS

- For access to

the terminal board, remove the rear panel of the appliance. Loosen the cable gripper and allow

the cable to pass through. Locate the conductors so that the earth cable is the last to detach

from its terminal in the event of reverse pulling. Connect the phase conductors on the terminals

marked “L1” and “L2”, the neutral conductor to the terminal marked “N”, and the earth

conductor to the terminal marked with symbol according to the following lay-out:

380 - 400V~ 2N

N L

(this electrical connection lay-out is also available near the power supply terminal board).

Tighten the cable gripper and re-fit the rear panel of the appliance. The appliance must be

connected to an unipotential system whose efficiency must be suitably verified according to

current legal regulations.

This connection must be made between different appliances using the terminal marked with

the symbol

. The unipotential conductor must have minimum diameter of 10 mm

. The

unipotential terminal is located low down at the rear of the appliance.

The power cable must comply with the following characteristics:

KCP96 V – KCP96 VS

KCR 96 V

KCP5 96 V – KCP5 96 VS – KC 96 V – KC 96 VS

KC 96 M – KC 96 MS

Power supply voltage (V~) 220 – 230 380 – 400 2N

Power cable diameter 3x1.5 mm

4x2.5 mm

Type of power cable H07RN-F

Safety device - The appliance is supplied with a manually resetting thermal breaker to protect

against excessive, dangerous temperatures which could be accidentally generated inside the

oven. If tripped, the device cuts out electrical power to the appliance. To access this device,

remove the panel at the rear of the appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi KC 96 MS Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hendi KC 96 MS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info