Bedienungsanleitung Hendi KCP 96 V (Seite 11 von 26) (Englisch)

741187

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

_ Electric Cookers _ rev. 1 ______________________ KCP96 V – KCP96 VS – KCP5 96 V – KCP5 96 VS – KC 96 V –

KC 96 VS – KC 96 M – KC 96 MS – KCR 96 V _

_ CATEGORY II2H3+ _ GB __

0705

_____________________________________________________ page 11 _

6. Adapting cook-top to different types of gas

Mod. KCP96 V – KCP96 VS – KCP5 96 V – KCP5 96 VS

To adapt the hob to a type of gas that differs

from the one tested in the factory (see data plate

or supplementary plate), replace the nozzles of

the five burners Remove the pan carrier grilles

from the hob and withdraw the movable parts of

the burners from their seats:

- Remove the pot support grids from the

cook-top and remove the mobile parts of

the burners from their position.

- Unscrew the jets (Fig. 2) using the 7 mm.

Key and replace them with the new ones

(see table 1). Check the exact

correspondence of the diameter indicated

on the table with that printed on the jets.

After having replaced the jets, set up all the

parts again and stick the new data on the

technical data plate.

Fig. 2

N.B. The burners don’t need any air regulation.

Minimum level adjustment - Burner minimum levels are preset for methane gas (G20)

operation. If operating on liquid gas (G30/G31) proceed as follows: ignite the burner at

minimum position, and, using a screwdriver, fully tighten the by-pass adjustment screw at the

side of the shank of the relevant tap. Check if the flame remains stable and uniform – to help

you check, rapidly turn the tap knob from maximum to minimum position. When you have

finished adjusting the by-pass valve, seal it with red paint. Make sure you fit a plate with the

new installation data. After having set the by-pass screw, seal it with red varnish.

Gas pressure (mbar)

Type of gas Normal Max. Min.

Table 1

G30 30 35 20

G31 37 45 25

G20 20 25 17

Main nozzles diameter

(1/100 mm)

By-pass screw nozzles

diameter

(1/100 mm)

Consumption calculated with gross

heat values

Nominal

thermal

capacity

(kW)

Reduced

thermal

capacity

(kW)

G30/G31

30/37mbar

G20

20mbar

G30/G31

30/37mbar

G20

20mbar

G30

30mbar

(g/h)

G31

37mbar

(g/h)

G20

20mbar

(l/h)

Triple crown

burner Nr. 1

3.5 1.8 95 135 74 Regul. 255 250 334

Fast burner

Nr. 3

3 0.95 85 115 50 Regul. 218 214 286

Semi-fast burner

Nr. 1

1.75 0.6 65 97 40 Regul. 127 125 167

Mod. KC 96 V – KC 96 VS – KC 96 M – KC 96 MS – KCR 96 V

To adapt the cook-top to a different type of gas from the one used to test the device in the

factory (see data plate or supplementary plate), replace the nozzles of the five burners and set

the primary air flow by means of the appropriate tools. To do so it will be necessary to

disassemble the cooker cook-top in order to easily access the burners, the nozzle holders and

the tools used to adjust the primary air. Proceed as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi KCP 96 V Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hendi KCP 96 V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info