Bedienungsanleitung Hendi 221808 (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

742598

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

• Tighten the screws ﬁrmly but do not over tighten. Over tightening can damage the screws,

greatly reducing the holding power.

• During installation, keep away the pet and children.

• Do not insert any objects into the air intake or exhaust. (risk of electric shock).

• Do not cover the appliance. (risk of overheating).

• Do not block the exhaust. (risk of triggering the thermal fuse).

• Do not allow contact with liquids. (risk of short-circuiting).

Intended use

• The appliance is intended for professional use.

• The appliance is designed only for drying hands.

Any other use may lead to damage of the appli-

ance or personal injury.

• Operating the appliance for any other purpose

shall be deemed a misuse of the device. The user

shall be solely liable for improper use of the de-

vice.

Grounding installation

This appliance is classiﬁed as class I protection

appliance and must be connected to a protective

ground. Grounding reduces the risk of electric

shock by providing an escape wire for the electric

current. This appliance is equipped with a cord

hav¬ing a grounding wire with a grounding plug.

The plug must be plugged into an outlet that is

properly in¬stalled and grounded.

Preparations before installation

Before installation: Check the appliance and its

screw holes at the back for any damage.

Note: Installation kits (included) and consult a

qualiﬁed contractor or installer if you are not cer-

tain the structure of the structure of the wall and

ensure that the procedure is carried out properly

and safely.

• Important: make sure the appliance is mounted

within the reach of the electrical outlet.

• Important: do not mount the appliance on dry-

wall or panelling without ﬁrst anchoring to a wall

stud.

• Important: before start mounting, make sure you

have all the tools, such as screw driver, electric

drills, measuring tape, marking pencil (not in-

cluded).

• The appliance must be securely anchored on the

wall by attaching the screws

• Locating the wall studs: anchoring the assures

that the appliance will not loose during operation.

Be aware that items such as ducts, electrical

wires and water pipes may be behind the walls

in your work area.

• For attaching the appliance securely to other wall

surfaces such as concrete or brick, see your local

hardware store for recommendations on using

the appropriate concrete and masonry fasteners

and anchors for your particular structure.

Installation on the wall

Attention: Installation should be performed by a

professional installer or electrician.

1) Drill four holes (ø 8 mm) in the wall (for position

of the holes check Illustration 1 and 2). Put the

wall plugs into the holes

2) Remove the two screws that keep the cover in

place and remove the cover. (Illustration 3)

3) Pull the wires through the hole and ﬁx the appli-

ance to the wall with 4 screws, then connect the

power wire to a power source (the ground wire is

yellow and green). (Illustration 4)

4) Close the cover and secure it with the two screws

from step 2. (Illustration 5)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 221808 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info