Bedienungsanleitung Hendi 223376 (Seite 20 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

741897

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

• ON/OFF

When power is supplied to the oven the control panel lights up and the operating display indicates tempera-

ture in cooking chamber.The oven now is ready for operating.

• START/STOP COOKING PROGRAM

This button starts/stops a previously set program or cooking cycle.

• TEMPERATURE SELECTOR

When the oven is on “ON” the temperature display shows the temperature in the cooking chamber.To set the

desired cooking temperature press the temperature selector and press (+) or (-) buttons for INCREASE or

DECREASE. The temperature display will show the set value. Press the temperature button for conﬁrmation

or wait 5 seconds and it will automatically be conﬁrmed. Values go from 30°C to 260°C.

During cooking the CHAMBER display shows actual internal chamber temperature and to see the set tem-

perature you must press “temperature button”. Heating element led is on red when the heat is on and green

when it is off.

• TIMER

Press Timer button, to set the time value by acting on (+) or (-) for INCREASE or DECREASE. The time which

appears on the display must be conﬁrmed pressing the timer button or wait 5 seconds for automatic conﬁr-

mation.

The programmable times range is 999 minutes.

Acting on the timer button if you go under value of “1” on display you will see “----“: means “inﬁnite time” the

oven will continue to work with the set parameters until START/STOP button is pressed. The time display will

start count-up so you can see from how long the oven is operating.

In case you set minutes on the time display will start countdown during cooking.

• STEAM

Enables humidifying in manual cooking or to program the various humidity settings during process.

- Humidifying in manual cooking: during cooking, the STEAM button enables the release of steam into the

cooking chamber for as long as it is pressed. The STEAM led will be on. If the motor turns the other way (only

for models with inverter system), humidifying will stop brieﬂy.

- To program automatic humidifying during cooking: after pressing the STEAM button, it is possible to in-

crease or decrease the humidity by pressing + / -. It ranges from: OFF – 20% - 40% - 60% - 80% - 100%.

During programming the values ﬂash on the display and pressing STEAM again will memorize them or wait 5

seconds for automatic conﬁrmation.

- During cooking, the STEAM led goes on when steam is being released into the cooking chamber and it stop

brieﬂy when the motor turns the other way (only models with inverter system).

- During cooking, keeping the STEAM button pressed enables manual humidifying at any time for as long as

it is pressed.

The set of humidiﬁcation is allowed only before running a cycle. To change the set of humidiﬁcation: press

STEAM button and on the Display 1 show „hum”, the Display 2 (DISP2) show ﬂashing the set-humidiﬁes, with

+ / - button you change its value.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 223376 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info