Bedienungsanleitung Hendi 227060 (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

741830

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

RESET with the SAFETY CUT-OUT

Please note that there is a SAFETY CUT-OUT device

for protection located at the lower rear side of the

appliance with a protective cap. This is to turn off

the appliance automatically when the temperature

is too high.

• Unplug the appliance from the electrical outlet

ﬁrst.

• Allow the appliance to completely cool down.

• Unscrew (tool not supplied) the black protective

cap of the “SAFETY CUT-OUT”.

• Push the button to RE-SET the overload circuit.

You should hear a click sound.

• Screw back the protective cap on the “SAFETY

CUT-OUT” button.

Cleaning and Maintenance

Warning!

• Always disconnect the appliance and open the

door to allow it to cool down completely before

cleaning.

• Never use abrasive sponges or detergents, steel

wool or metallic utensils to clean the interior or

exterior parts of the appliance.

• Avoid the use of sprays as this may damage the

appliance’s surface.

• The appliance should be cleaned regularly and

any food deposits removed.

• Wipe out any remaining oil or fat.

• Note: The trays holder on two sides can be un-

screwed (tools not supplied) to detach for clean-

ing.

Parts How to clean Remark

All accessories such as trays, tray

handle, tray holders

- Soak in warm, soapy water for about 10 to

20 minutes

- Rinse under running water thoroughly.

Dry all parts well at last.

External housing - Wipe clean with a soft cloth and a little mild

detergent. Make sure no water or moisture

enters inside of the appliance.

Inside of the appliance - Remove any food deposits.

- Wipe with a damp cloth and a little cleaning

detergent to remove any spills or splatters.

- Note: Be sure not to damage the heating

elements.

Glass door

Storage

• Always make sure the appliance has already

been disconnected from the electrical wall outlet

and cooled down completely.

• Store the appliance in a cool and clean place.

Troubleshooting

If the appliance does not function properly, please

check the below table for the solution.

If you are unable to solve the problem, please con-

tact the supplier/service provider.

Problem Possible cause Possible solution

When connected to the electrical

power outlet, the control settings are

made & indicator lights are on. But the

appliance does not heat up.

The thermostat is defeated Take the appliance to your supplier or

service provider for repair.

At least one of the heating element is

burnt out.

When connected to the electrical

power outlet, the control settings are

made. It heats up normally. But the

indicator is not on.

The indicator light is defective. Take the appliance to your supplier or

service provider for repair.

Neither the indicator nor the heating

element works.

The power cord & plug is not connect-

ed ﬁrmly with the electrical power

socket.

Check again the connection. And

make sure all the connections are

ﬁrmly connected.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 227060 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info