Bedienungsanleitung Hendi 239438 (Seite 7 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

741240

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

4) If the appliance beeps after being switched on

and placed cookware, the cookware which is

not suitable for induction or the appliance is

defective. In case of any doubt, always contact

the supplier of your cookware!

Set power / temperature / timer by following description

Setting Power

/ Temperature level

• During operation, press the Temperature setting

(5) / Power setting (6) to choose different func-

tion. The corresponding indicator lights up.

• Press the Increase setting (2) or Decrease set-

ting (4) to increase or decrease the power level

(Range: 100W ~ 1,700W for front; 100W ~ 1,800W

for rear) or temperature level (Range: 35ºC -

240ºC for both). Default setting is 100W / 35ºC

separately.

• Higher power level is suitable for steaming. And

higher temperature level is suitable for roasting,

grilling or frying.

Setting Timer

• After power or temperature setting for cooking,

you can opt for timer setting. Press the timer

function (7) to activate. The indicator light (7)

lights up.

• The timer shown on the digital display (3) is in

the form 0:00 (where 0 = 1, 2 or 3 hour; 00 = 01 ~

59 minutes).

• Press the Increase setting (2) or Decrease set-

ting (4) to increase or decrease the cooking time

(Range: 0 min ~ 180 mins). Default setting is 0

min.

• When the timer is set, it will be stored automat-

ically within 5 seconds. The appliance will then

start operation. It will display the remaining time

and the power setting / temperature setting al-

ternately on the display (3).

• The appliance will switch off when the set time

is elapsed and all the light indicators will go off.

Note:

1) Press and hold the increase setting button (2) or

decrease setting button (4) for fast adjustment.

2) After an extended period of operation, it is nor-

mal for the cooling fan inside to continue run-

ning in Standby mode for some time. Before

unplug the appliance, wait until the cooling fan

stops running.

3) The appliance’s surface is still hot even after

switch to Standby mode. Wait completely cool

down before touching.

Error codes display

Error codes shown on the display (4) Possible cause Possible solution

E 1 The temperature of the appliance is

too high

Clear all obstacles that around the

appliance. Unplug the appliance, re-

move the pan or pot, wait until the ap-

pliance is completely cool down.

Cooling fan defective Contact the supplier.

E 2 The pan or pot is overheated.

Possibly, the pan becomes empty and

appliance will shut down for protec-

tion.

Unplug the appliance, remove the

pan or pot, wait until the appliance is

completely cool down. And make sure

water is inside the pan.

E 3 The supply voltage is abnormal. (Sup-

ply voltage is too high or too low)

Make sure that the appliance is con-

nected to a suitable electrical power

supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 239438 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info