Bedienungsanleitung Hendi 225523 (Seite 6 von 128) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

741836

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

The manufacturer and dealer is not liable for any

inaccuracies due to printing errors or transcrip-

tion, in this manual. In line with our policy of con-

tinuous improvement products, we reserve the

right to make modification of the product, pack-

aging and specifications contained in the Docu-

mentation without prior notice.

5. INSTRUCTIONS FOR THE INSTALLER

The following instructions are aimed at the quali-

ﬁ ed installer, to ensure that he carries out the in-

stallation, adjustment and maintenance operations

as correctly as possible and according to current

legal regulations. Any operation must be per-

formed with electrical power cut to the appliance.

Before using the appliance, carefully remove the

special adhesive ﬁ lm protecting the parts in stain-

less steel. Do not leave any glue residues on the

surfaces. If necessary, remove them at once, with

an appropriate solvent.

5.1 FITTING THE FEET

The feet are inside the appliance and must be secured on the four threaded holes on the base. If necessary,

the height of the feet can be adjusted by screwing or unscrewing.

5.2 POSITIONING

Position the appliance perfectly horizontally on a ta-

ble

or similar support (the table or support must

be at least 85 cm above the ﬂ oor). Position it at a

distance of not less than 10 cm from the side and

rear walls, to enable natural ventilating air to cir-

culate freely around it. The appliance is ventilated

through speciﬁ c openings on the metal walls of the

outer housing, and ensures efﬁ ciency and long-life.

For this reason it is strictly forbidden to obstruct

these ventilation openings, even partially or for

short periods. Failure to observe this speciﬁ c pro-

hibition releases the manufacturer of the appliance

from all responsibility and immediately voids any

guarantee rights for the said appliance, because its

constructive conformity has been voluntarily com-

promised. Furthermore, the appliance is not suita-

ble for embedding and for grouped positioning with

other identical appliances.

5.3 ELECTRICAL CONNECTION

The appliance must be connected to the electri-

cal mains according to current legal regulations.

Before making the connection, make sure of the

following:

• the voltage and frequency values of the power

supply system match the values on the “technical

data” plate afﬁ xed on the appliance;

• the limiting valve and the system are able to

support the appliance’s load (see the “technical

data” plate);

• the power supply system has an adequate earth

connection according to current legal regulations;

• a omnipolar switch with minimum between-con-

tacts aperture of the overvoltage category III

(4000 V), sized to the load and conforming to

current legal regulations, is ﬁ tted between the

appliance and the mains in the direct connection

to the mains;

• the omnipolar switch used for connection is easy

to reach when the appliance is installed;

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 225523 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info