Bedienungsanleitung Hendi 239506 (Seite 5 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

741560

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Preparations before using for the first time

• Check to make sure the appliance is undamaged.

In case of any damage, contact your supplier

immediately and do NOT use the appliance.

• Remove all the packing material and protection

ﬁlm (if applicable).

• Clean the appliance with luke-warm water and

a soft cloth.

• Place the appliance on a level and steady surface,

unless mentioned otherwise.

• Make sure there is enough clearance around the

appliance for ventilation purposes.

• Position the appliance in such a way that the plug

is accessible at all times.

Operation

Important: Prior to using the pan and lid, clean

them thoroughly.

1. Adjustment: Turn the thermostat knob to “Off”

and plug the thermostat into the pan.

2. Connect the power plug to a suitable electrical-

wall outlet.

3. Turn the thermostat knob to the temperature re-

quired for the dish that is to be prepared.

4. To switch off or remove the thermostat, turn the-

knob to “Off”.

NOTICE: Ensure that you connect the thermostat in

the appropriate manner. When removing the ther-

mostat, never pull the lead but grip the plug itself

to remove it.

Boiling, frying, and pot-roasting

Wait approximately 5 to 10 minutes after the pan

has been switched on. When the indicator lamp is

lit, you can start to use the pan.

• When in use, the indicator lamp ﬂashes. This

does not indicate a fault, but shows that the ther-

mostat is operating correctly.

• A hissing sound heard when using the pan does

not indicate a fault. This noise originates from the

heating element and the party pan.

• Do not touch hot dishes with your hands, do not

put ﬂammable objects on the pan.

After use

1. After using the pan, turn the thermostat knob to

“Off”.

2. Then remove the plug from the power outlet

and remove the thermostat from the party pan.

Caution: The temperature sensor of the thermo-

stat will be very hot after the party pan has been

used. Therefore, ﬁrst allow the party pan to cool

down before removing the thermostat!

3. After allowing the pan to cool down, cover the ther-

mostat socket to prevent water entering it during

cleaning. Clean the party pan with a soft sponge.

Then wipe the device with a dry and soft cloth.

Precautionary measures when using the party pan

The party pan has a non-stick coating. Therefore

take note of the following:

• Do not use sharp metal objects (if you wish to cut

meat that has been cooked in the pan, ﬁrst re-

move it from the pan and cut it on a board/plate).

• Do not use a knife to cut meat in the pan.

• Do not put the thermostat on the party pan, it

should never come in contact with the pan.

• Do not use detergent, or a nylon or metal brush.

They will damage the non-stick coating of the

pan.

• The pan must be cleaned with a wet cloth after

use. Fat remaining on the surface can cause a

ﬁre.

• Never use aggressive cleaning agents or abra-

sives. Do not use any sharp or pointed objects.

Do not use petrol or solvents! Clean with a damp

cloth and detergent if necessary. Do not use

abrasive materials.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 239506 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info