Bedienungsanleitung Hendi 226896 (Seite 11 von 44) (Englisch, Polnisch)

741917

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

The ﬁ rst commissioning must be carried out pro-

ceeding as follows:

• clean the front part of the oven with a clean

and soft cloth in order to remove any eventual

residues;

• connect the plug to the socket;

• put the switch of heating elements (pic.3;4;5-

ref.3) in pos.”i”; for the ovens 1/40 and 2/40: press

the general switch (pic.1;2-ref.7);

• Start the heating elements setting the thermo-

stat (pic.1;2;3;4;5-ref.2) on the temperature of

150°C. The red warning lights signaling the op-

eration of the heating elements is on;

• let the oven heating up for about 1 h;

• switch the heating elements off by putting the

switch in (pic.1;2;3;4;5-ref.2) in position “0” the

warning light turns off; for the oven 1/40 and

2/40: press the general switch and turn off the

heating elements;

• open the door and keep it opened for about 15 min

in order to let steam and smell to go out;

• close the door and repeat the process de-

scribed in section 4) bringing the thermostat

(pic. 1;2;3;4;5 -rif.2) at the temperature of 400°C

for the oven 1/40 and 2/40: bring thermostats

(pic.1;2-ref.2) at a temperature of 350°C.

• let the oven heating up for about 1 h;

• switch the heating elements off by putting the

switch in (pic.1;2;3;4;5-ref.2) in position “0” the

warning light turns off; for the oven 1/40 and

2/40: press the general switch and turn off the

heating elements;

• turn off the oven as described in par. 5.4

• with the oven 1/40 and 2/40 you can adjust the

cooking time by setting the minutes with the

timer (pic.1;2-ref.6). at the end of the time set

the heating elements will turn off. To choose the

mode of cooking continued, bring the timer knob

(pic.1;2-ref.6) to “on” by turning to the left

5.3 TURNING ON OVEN

• Connect the plug of the power supply cable to the

power supply outlet;

• Put the switch of heating elements (pic.3;4;5-

ref.3) in pos.”i”; for the ovens 1/40 and 2/40: press

the general switch (pic.1;2-ref.7);

• Start the heating elements setting the thermo-

stat (Pic.1;2;3;4;5-Ref.2) to the desired tempera-

ture indicated on the handle. The related warning

lights signaling the heating elements in use are

switched on;

• Once the oven has reached the desired tempera-

ture (see point 9 of this paragraph), visible on the

thermometer (Pic.5-Ref.4), it is possible to insert

the pizza;

• Open the oven door manually using the handles;

• To illuminate the inside of the chamber, press the

oven lamp switch (Pic.5-Ref.5);

• Insert the pizza/pizzas using suitable devices. It

is important to avoid leaving the door open for too

long, since the outgoing heat lowers the temper-

ature of the oven.

• Close the door again and check the backing

through the inspection glass ;

• The baking temperature of the pizza varies if it is

positioned directly on the refractory stone or on a

baking tray. In the ﬁ rst case, it is suggested to set

the backing temperature at 280°C on the bottom

and 320°C for the ceiling; in the second case, set

320°C for the bottom and 280°C for the ceiling;

• When the baking process ends, open the door

and extract the pizza /pizzas and colse the door

again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 226896 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info