Bedienungsanleitung Hendi CM1089A (Seite 256 von 264) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Norwegisch)

741731

256

Zoom out

Zoom in

Vorherige Seite

1/264

Nächste Seite

English - 16

English - 17

MULTI - STAGE COOKING.

1. Upon pressing the PROG button, the oven will enter

Program mode. The display will be cleared.

2. Using the Number buttons, enter the program number from

1 to 20.

3. Then, press the Power Level button to select power.

By pressing the Power Level button repeatedly, you can

select the power level - HI, MED, or LOW.

4. Use the Number buttons to enter the cooking time. You can

set a time from one second to 30 minutes. To set a time

over one minute, enter the seconds as well.

For example, to set 10 minutes, enter 1, 0, 0, 0.

5. Repeat step 3 and 4 for II or III stage memory

proggramming.

6. Press the PROG button to complete setting the memory.

The display will show ‘0’.

The maxium allowable cooking time is 30 min. If the time exceed 30 min, the display

will show “E3”, then press Stop/Cancel button and repeat the steps.

USING MEMORY PROGRAMMING.

Press the Number buttons to select user-programmed memory functions (please refer to

memory programming) from 1 to 20.

Press the Start button.

IftheDEFROSTfunctionisincludedinSTAGECOOKING,itworksatrst.

If you want to change program, just reset MEMORY PROGRAMMING.

USING THE CHECK BUTTON

ConrmingthecookingtimeandPowerLevelineachmemoryprogram.

1. ClearalloperationsbypressingtheStop/Cancel button.

Press the CheckbuttontoenterCheckmode.

2. Using the Number buttons, enter the program number from

1 to 20.

For example, suppose you press ‘5’, for the Memory

Program 5 which is HI Power Level, I Stage cooking with a

time of 6 minutes and 30 seconds, 6:30.

First, ‘5’ will be displayed. but will change to show the

3. After one second, the display will clear automatically.

If you want to check other Memory Programs, just enter the

Memory Program numbers.

4. Press the Stop/Cancel bottontoexittheCheckmode.

ReadingeachMemoryProgram’sCycleCounter

1. ClearalloperationsbypressingtheStop/Cancel button.

Press the CheckbuttontoenterCheckmode.

2. Press the Start button, and then press any Number button,

from 1 to 20, and the number of cycles for that particular

Memory Program will be displayed. The cycle count is

displayed in units of 10.

For example, if Memory Program 5 has been used

100times, the display will show ‘10’.

3. After one second, the display will clear automatically. If

you want to check other Memory Programs, just enter the

Memory Program numbers.

4. Press the Stop/Cancel buttontoexittheCheckingmode.

As the display uses units of 10, the cycle counts are approximate. The cycle count

displayed increases every ten cycles.

For example, if the cycle count were 90-99, “9” would be displayed, The “9” would

change to “10” on the 100th cycle. The cycle counter function has a limit of 99,990

cycles. Once that number is exceeded, the cycle counter will automatically clear and

start again from “0”.

CM1089A_XEU_DE68-03310E-03_EN_160629.indd 16 2016-06-29 �� 2:56:15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi CM1089A Seite 256

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info