Bedienungsanleitung Hendi 232163 (Seite 8 von 176) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

742361

Zoom out

Zoom in

Vorherige Seite

1/176

Nächste Seite

4. Electrical connection and earthing

Electrical power supply

The installation and the electrical con-

nections must be carried out in con-

formity with the electrical rules in

force. These operations must be carried out by

qualiﬁed staff. The company declines any responsi-

bilities originated from the no observance of the

above rules in force.

See the blast chiller electric diagrams at the end of

this manual.

Before plugging in the blast chiller, it is necessary

to proceed with its complete and careful cleaning,

using warm water with no aggressive detergents

and drying with a soft cloth all the humid parts

(read with attention the chapter regarding the blast

chiller cleaning).

In order to carry out a correct plug in you must pro-

ceed as follow:

• Prearrange a thermal magnetic circuit breaker

switch and be sure that the frequency/tension of

the line corresponds to that shown on the blast

chiller serial number label (see the label plac-

ing).

• Verify the supply tension at the socket, it must be

between +/- 10% when you start the compressor.

• We recommend you to install a bipolar-switch (or

4 square pole switch) with contact opening of at

least 3 mm, at the head of the socket. This switch

is obligatory if the loading is over 1000 W or when

the blast chiller is connected directly without the

use of the plug. The mag thermic switch has to be

placed nearby the blast chiller in order to be well

seen by the technician in case of maintenance.

It is necessary that the power supply cable section

is adequate to the unit power consumption.

The earthing of the appliance is compul-

sory in conformity with the law. Therefore

it is necessary to connect it to an efﬁcient

earthing system. If the power supply cable was, it

must be substituted by the technical qualiﬁed staff.

It is strongly recommended to avoid the use of elec-

trical appliance inside the blast chiller compart-

ment.

• If the compressor is damaged, it must be re-

placed exclusively by qualiﬁed staff, in order to

prevent any risks. In case of breakdown we sug-

gest to unplug the appliance and to use a high

sensitivity mag thermic anti-electrical shock

switch.

Starting the blast chiller

ATTENTION!

The ﬁrst start up must be carried out by qualiﬁed

staff.

Before switching on the blast chiller, be sure that:

• Your hands must be dry

• The surface of the blast chiller must be dry

• The ﬂoor and the electrical socket must be dry

Furthermore, be sure that:

• The build in condensing unit blast chiller must be

carried only in upright position. If it had leaned,

we recommend to wait at least 8 hours before

proceeding with the start so that the oil will ﬂow

in all the components, lubricating them again.

For the temperature setting make reference to the

corresponding chart about product categories/ us-

age temperature, in addition For the working pa-

rameters regulation refer to the user instructions

of the control panel enclosed to this current manu-

al.

Once the blast chiller is connected with the power

cable (see the previous paragraph), proceed pow-

ering it with the switch closing.

For the built in unit, before plugging it in, verify that

the selector is open in 0, OFF or green position. In-

sert the socket and then turn off the switch. Before

placing inside the food to be chilled or frozen, it is

necessary to clean the chamber of the appliance

(see chapter about cleaning) and afterwards it will

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 232163 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info