Bedienungsanleitung Hendi 272602 (Seite 9 von 144) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

742602

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Connecting to a gas cylinder

• Recommend to use 9kg gas cylinder or refer to

your gas supplier for suitable gas cylinder.

• Refer to your gas supplier for instructions on the

use of your gas cylinder.

• Only change gas cylinders outdoors or in a well

ventilated area away from naked ﬂames and any

other source of ignition.

• The gas cylinder must always be used in an up-

right position.

• Close the heater control knob by turning fully

clockwise.

• Close the gas cylinder tap and then attach the

regulator onto the gas cylinder.

• Tighten all connections ﬁrmly and with a spanner

where appropriate. The cylinder should be locat-

ed on the cylinder base.

• Check for leaks at all joints using soapy water. If

a leak is found, tighten the joint and then re-test.

Important safety rules

For use outdoors or in amply ventilated areas.

An amply ventilated area must have a minimum of

25% of the surface area open.

The surface area is the sum of the walls surface.

The use of this appliance in enclosed areas can be

dangerous and is PROHIBITED.

Children and adults should be aware of the high op-

erating temperatures of areas above the post when

operating this heater. Children should be carefully

supervised when in the vicinity of the heater.

NEVER hang anything, including clothes or any

other ﬂammable items, on this heater.

DO NOT operate this heater unless it is fully as-

sembled with its reﬂector in place.

Respect the minimum clearances from combus-

tible materials.

The length of the gas hose may not exceed 1,5 meters.

Ceiling / Overhang

1 mtr

Wall

Maintenance

To enjoy years of outstanding performance from

your heater, make sure you perform the following

maintenance activities on a regular basis:

• Keep exterior surfaces clean.

• Use warm soapy water for cleaning. Never use

ﬂammable or corrosive cleaning agents.

• While washing your unit, be sure to keep the area

around the burner and pilot assembly dry at all

times. If the gas control is exposed to water in

any way, DO NOT try to use it. It must be replaced.

• Airﬂow must be unobstructed. Keep controls,

burner and circulation air passageways clean.

Signs of possible blockage include:

• Gas odor with extreme yellow tipping of ﬂame.

• Heater does NOT reach the desired temperature.

• Heater glow is excessively uneven.

• Heater makes popping noises.

• Spiders and insects can nest in burner or oriﬁces.

This dangerous condition can damage the heater

and render it unsafe for use. Clean burner holes

by using a heavy duty pipe cleaner. Compressed

air may help clear away smaller particles.

• Carbon deposits may create a ﬁre hazard. If any

carbon deposits develop, clean dome and engine

with warm soapy water.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 272602 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info