Bedienungsanleitung Hendi 975251 (Seite 8 von 116) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

741174

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

5. Press SET button again (change to another

parameter) - “SEALING” LED will light up to

indicate sealing time. Set the desired value by

pressing “+” to increase or ”-” to decrease seal-

ing time. Time range is 0-3.5 seconds. Sealing

time should be gradually increased.

6. Press SET button again (change to another

parameter) - “COOLING” LED will light up to

indicate cooling level. Set the desired value by

pressing “+” to increase or ”-” to decrease cool-

ing time. Time range is 0-9.9 seconds.

7. Press SET button again - parameter LEDs will

switch o.

8. Press SEALING TEMP button repeatedly to set

the sealing power. Each press will switch on bag

sealing power LEDs (HIGH, MIDDLE, LOW). De-

pending on bag thickness, proper sealing power

will be used. The thicker the bag, the higher the

power.

9. Insert the bag in machine’s chamber. Make sure

that the whole length of the bag is placed on the

sealing bar and that the bag is not folded along

the seam.

10. Press the bag onto the sealing bar using a met-

al clamp.

11. Close the upper cover of the machine and hold

for a while. The machine will start working au-

tomatically. The cover will be sealed shut.

12.

During operation the chamber will generate vacu-

which will prevent accidental opening of the

cover.

All processes are carried out in the state of vac-

uum, the display and timer show the current

process (time remaining to generate full vacu-

um, sealing time and then cooling time). During

operation “WORKING” LEDs will switch on.

13. After completion the cover will automatically be

raised and “Ed” message will be displayed.

14. After completion of the cycle, the chamber is

lled with air, the cover opens automatically

and “Ed” is displayed. The cover will not open

automatically if a locking clamp is used. Unlock

the clamp to open the cover.

15. To continue working at the same parameters,

close the machine’s cover after inserting anoth-

er bag.

16. After completion of work turn the machine o

with the “OFF” switch, ip the blue switch at the

back of the machine downwards and disconnect

power cable from the mains.

NOTE: never obstruct air ow vent in the chamber.

NOTE: In an emergency press “STOP” to stop the

vacuum packaging process. The chamber will be

lled with air thus completing the process, the cov-

er will open after the process is completed. The

cover will not open automatically if a locking clamp

is used. Unlock the clamp to open the cover.

NOTE: in models 975251, 975268, 975275 the

GAS” parameter/function is not active.

NOTE

• Do not turn the machine on without any bag

inside. Doing so will accelerate the wear of the

heating element.

• Turn the machine o and disconnect the power

cable if the machine will not be used for some

time.

• The vacuum gauge/meter reading may be dier-

ent in dierent areas. At high altitudes, the data

in vacuum meter goes down.

• Do not use vacuum bags that emit poisonous va-

pours while sealing – use dedicated Victor Vac-

uum Bags.

• The machine must be transported in a horizontal

position.

• The transport must proceed strictly according to

the instructing marks on the shipping case.

• The machine should be stored in dry, ventilated

place and room temperature.

• Please be careful during the automatic opening

of the acrylic cover to avoid being hit.

• Please do not try to make any repairs without

consulting professional service rst.

• Please use spare parts delivered with the ma-

chine or recommended by the manufacturer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 975251 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info