Bedienungsanleitung Hendi 230442 (Seite 12 von 144) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch)

742508

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Note: excessive time of filing the brine tank may

cause the overflow of water to sewage or outside

of the device. The supplier of the device shall not

be held responsible for any damages resulting

from improper setting of this parameter.

• (5) Fast rinse - time of fast rinse. E.G., 5 - 10M

time of the 5th cycle of operation is 10 minutes

(m - indication in minutes)

• The type of external signal send by the head. B-01

– a permanent signal during entire regeneration

(from the moment of leaving “in serv” position

to the moment to returning thereto. “In serv” –

signal only when the head changes its position

(head’s servo working).

mmol / l mval / l

mg CaCO3 / l

(ppm)

German

degree

French

degree

gpg

1 mmol / l = 1 2 100 5.6 10 5.8

1 mval / l = 0.5 1 50 2.8 5 2.9

1 mg CaCO3 / l = 0.01 0.02 1 0.056 0.1 0.058

1 German degree = 0.179 0.357 17.9 1 1.79 1.04

1 French degree = 0.1 0.2 10 0.56 1 0.58

1 gpg = 0.143 0.29 14.3 0,8 1.43 1

Sample controller programming:

If the keypad lock symbol is present on the display,

it has to be unlocked by pressing and holding up

the up [11] and down [12] button, until the key sym-

bol disappears.

1. In order to activate the setting change mode, the

Enter [9] button shall be pressed.

2. The [8] and [6] symbols will be lit in the settings

change mode. It will inform that the display

shows the current time. The colon (”:”) symbol

will be blinking between the indicator of hour

and minutes.

3. In order to activate the current time change

mode, the enter [9] button shall be pressed.

The indication of time and the [8] symbol will

start blinking.

4. In order to adjust the indication of hours, the up

[11] and [12] down buttons must be pressed cor-

respondingly.

5. In order to conﬁrm the setting selected, the en-

ter [9] button shall be pressed. The selected in-

dication will be accepted and the controller will

go to the minutes setting mode.

6. In order to adjust the indication of minutes, the

up [11] and [12] down buttons must be pressed

correspondingly. In order to conﬁrm the setting

selected, the enter [9] button shall be pressed.

The controller will conﬁrm changing the time

with a short sound signal and will return to the

parameters setting mode.

7. In order to move to another option, the down [11]

button shall be pressed.

8. In order to activate the mode of changing anoth-

er option, the enter [9] button shall be pressed.

The indication of time and the [8] symbol will

start blinking. With the down [11] and Up [12]

button, the desired value shall be chosen and

conﬁrmed with the enter [9] button.

The controller will conﬁrm changing the time

with a short sound signal and will return to the

parameters setting mode.

9. In order to activate the setting change mode, the

enter [10] button shall be pressed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hendi 230442 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info